cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2967
Views
0
Helpful
0
Comments
cdnadmin
Level 11
Level 11
This document was generated from CDN thread

Created by: Abdul Rasheed on 23-01-2012 05:51:50 AM
Hello,
              My name is Abdul Rasheed, i am working on a voice recording solution using SIP trunk and BIB.  It was noticed that while running the solution for 1 or 1.5 months in one site,  the recording will suddenly stop  and when i checked it was found that after the ACK is recieved from CUCM , it will immedietly send a BYE closing the session and the reason for the BYE is  Q.850 Cause =65  when i checked i found that the cause=65 means "bearer capability not implemented"  i am not sure why this error coming up immedietly on a working system after running for 1.5 months.  Is there any thing in CUCM configuration should i verify ?
 
Thanks and Regards
Abdul Rasheed

Subject: RE: SIP trunk - CUCM Rejection of SIP messages
Replied by: Abdul Rasheed on 09-02-2012 03:48:19 AM
Hello,
            can anybody tell me some reasons for the above error.   Why does a SIP message get a Q.850 cause =65 (bearer capability not implemented) error?


Regards
Rasheed

Subject: RE: SIP trunk - CUCM Rejection of SIP messages
Replied by: Abdul Rasheed on 19-02-2012 01:52:03 PM
Hello Everybody ,
           For the recording using BIB and SIP trunk,  the rejection of INVITE messages with a BYE  of reason "Bearer capability not implemented" what does this stands for ?  THis is not happening always, but at sometimes only.  Please let me know if anybody has got the same error and the possible reason . it will be a great help for me
 
 
Regards
Rasheed
 

Subject: RE: SIP trunk - CUCM Rejection of SIP messages
Replied by: Ahmed Fayomy on 24-02-2012 07:43:47 AM
Hello Abdul Rasheed;

i have the same bye message with the same reason, but my case is
1- SIP Trunk send me the invitations
2- my sip server response with 200 ok
3- SIP Trunk sent to my ACK 101   then he sent to me bye message and he cotinue in sending it.

i read about that my 200 ok response for the invitation should have the SDP and codecs, and if these codecs are not compatable with cucm
you will get that bye message.

my case is

1- i created SIP Trunk and give it my pc ip.
2- i run my sip application on my pc .
3- i got two invitations for the call on ip phone with automatic recording
4- i sent 200 ok for these two invitations
5- cucm sent me ack 101
6- cucm continue sending me bye message .

please if you ses that i missed any thing here,
like should i configure any thing in network or in my sip SAILFIN server or in CUCM configurations, tell me please,
Thanks,

Subject: RE: SIP trunk - CUCM Rejection of SIP messages
Replied by: Abdul Rasheed on 28-02-2012 11:42:12 AM
Dear Ahmed,
                          You have missed out a few messages during your SIP negotitations.  You need to go through the SIP trunk messaging guide available in the CDN website to implement those messages. 

regards
Rasheed

Subject: RE: SIP trunk - CUCM Rejection of SIP messages
Replied by: Ahmed Fayomy on 28-02-2012 04:51:45 PM
thanks Abdul Rasheed for your reply, now it is working, and the rtp streams came to my recorder pc.
but my problem is that i do not know how to save these rtp streams as a file [wav or mp3]., so if you know away to do please tell me to study it.
thanks again for your help

Subject: RE: SIP trunk - CUCM Rejection of SIP messages
Replied by: =?UTF-8?B?7Je07Zi4?= =?UTF-8?B?7IaQ?= on 21-09-2012 04:55:29 AM
i`m sorry but

could you show me a your "200 OK" messages?

i have a problem that cm does not send to me a 101 ACK messages

i don`t know what is the problem of my sip messages
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Quick Links