The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
I've got this interment problem where my ip phones aren't able to get an IP address from DHCP. I've got a mix of 9200L and 2960s POE switches. I've experienced the issue on both models, with different version of firmware on each. Different DHCP serve...
I get the regular connect and disconnect messages ie the 7220xx messages but I tested several bad password attempts and they do not get logged. is there a way to log this?Would be interested in creating an EEM that would alert on a significant amount...
Hi,I have a C9300U and T switch models.I wish to downgrade from 17.9.5 (ROMMON 17.9.2r) to 17.6.5.Do I need to downgrade the ROMMON version for 17.6.5?Thanks in advance
we are using Cisco Aironet 1815i Access Point as a WLC and Access point and need to be upgrade the firmware version 8.5.140.0 to 8.10.185.0. please suggest the step by step process that we need to be followed.
Hi, after upgrading the ASA SHIMO VPN app stopped working. I noticed that openconnect stopps working as well and to fix this issue for openconnect I just added --useragent=AnyConnect and it started to work. I tried to add this to shimo in expert mode...
I am using vwlc in conjunction with Cisco AP 2702i. I've configured two SSIDs with MAC filtering authentication. Certain APs are displaying a 2.5g connection, while others show a 5g connection.What could be the problem
Hi Guys.We are running Firepower 3140 Appliances. There are 2 * 40Gbps connection. The Physical (ETH2/1) 40Gbps interface has the MTU set as 9000 whilst the Sub Interface (ETH2/1.10) and (ETH2/1.20) has the MTU still at 1500In this scenario,1. Is the...
Hello, i still asking about how the network send the data to internet looks like. Can anyone help to explain.Every data we send to the internet will always pass through the ISP, which means the ISP can know the destination (and perhaps the contents o...
Hi,I want to secure one LAN port of my CBS350-48P switch. It is located to PoE camera outside the building.It would be great to shut down the port, if another device is put into this port.How can this be solved?Best regards,Heinz
Ive a pair of new UCS-FI-6536s and they are all set up and working fine in IMM but we cannot SSH to them as we did on the old FIs.They are on the same VLAN as the old FIs and there are no firewalls inbetween them.Does anyone know if this is even poss...
When upgrading from 7.2.5 to 7.2.7 this bug is also occurring. I have two TAC cases open prior to finding the error message and this documented bug, so we'll see if I get a response.
I want to use netconf to get status from C9800. module: Cisco-IOS-XE-wireless-access-point-oper +--ro access-point-oper-data +--ro ap-radio-audit-info* [wtp-mac radio-slot-id]
Hi anyone using radware as loadbalancer for wsa? Do we need to change anything in wsa side? We have given radware LB vip in the proxy settings of users but request is not reaching WSA.anyguide is available for the configurations.
Dear Community,I am running Cisco ASA 9.8. I have an app server sitting in the DM Zone that needs to be authenticated with Google Service (reCAPTCHA) only, but I am not allowing the internet service, not the application server. I have tried to apply ...
Trying to set up new sg350 10 p - tried using the config file from one used and working but it failed and needed factory resetmy other one has the leds turned off so have no idea what I should see ports 1 to 8 light green on left light only when usi...