The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hi all,I work for a mid sized financial firm with a total network device count of less than 100, mostly consisting of catalyst 9k (core and access switches), with handful of nexus 9k, MDS 9k, ISR4k, a pair of WLC5520s in SSO (AP3802s), and a dozen F...
Update:Looks like there's a discrepancy from one Version of Xterm to another, the commands are interpreted differently. This can be closed, thank you very much I'm trying to configure a CBS350 24T-4X with a pre written config file, it's not the first...
Hi I tried to write these commands in CLI (using Putty) for cisco ISR1100-4G but it seems like the VLAN command is not recognized.Regards,Aria Step 1Ensure that the router is in the factory fresh mode. If the router is not in the factory fresh mode,...
Hello! about profiling in ISE,I have seen in several tutorials that it is recommended to put a policy with an authorization profile (lets call it PROFILING) before the default bottom policy one named "Default". This PROFILING profile would have a dAC...
¡Saludos a todos!Esta es mi topología:La comunicación entre el Nexus y el Proveedor es por BGP, donde cada equipo tiene un solo ASN pero entre ellos hay un enlace físico por el cual pasan 2 VLAN (301 y 304). En la red que hice de laboratorio, estoy u...
Hello, I'm installing RTMT v14 on Windows 11. I've tried with both Oracle and Zulu versions of Java, both fail. Initially, Oracle gave issue saying JVM not available, so I uninstalled, switched to Zulu and amended all Environment Variables to match. ...
Hello,We had a power loss on our site - equipped with 6 * Aironet 1830 Mobility express Series.The "master" Aironet lost power, so we had to reboot the whole 6 APs.The method is as follows :- first shut down the 5 "slave" APs- verify that the "master...
So this is a topic that's been mentioned time and time again I'm sure but i wanted to get a bit more specific to my situation. We're replacing our core switch with a C9300 (we currently have a 3750). We have a pretty simple network. Any desk with a c...
Hello, to profile devices via DHCP , is it enough to use the device-sensor config for it, or I still need DHCP relay config to forward DHCP packets to ISE? device-sensor alone ? or device-sensor + dhcp relay (ip helper-address) Thank you. Regards
LLDP (Link Layer Discovery Protocol) Continuando a nossa série Cisco Basic Device Management, vamos falar sobre o protocolo de descoberta de vizinhançaLLDP, o Link Layer Discovery Protocol. O LLDP opera como uma opção aberta, multivendor (padrão IEE...
Hello,I want to set up a IPSec IKEv2 VPN to a central ASA. On my side we have a cisco 897.First I tried a crypto map configuration. Didn't work because the IKEv2 SA goes UP and immediately goes DOWN with the error message "IKEv2:(SESSION ID = 1,SA ID...
This is happening in our Lab environment, need to fix it so people can reskill and avoid it in Prod. After deploying ucce 12.5(2) on new Windows Server 2016 VMs, a security scan found Apache Tomcat Version 9.0.62 to be vulnerable and suggested to upg...
On my Windows 10 computer, I can connect to the VPN using AnyConnect 3.1.02026 without difficulty. However, once I disconnect, I need to reboot my computer to connect again. When I try to connect the second (and subsequent) times I get the message, "...
Hi , We use Cisco VPN and the SBL (start before login module) this works flawlsy but when the user locks his screen/auto lock there unable to get back in due to secutiry policys preventing Cached profiles and thus cannot login after a system locks , ...