Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello!I am a bit new to CUCM and all its glory, but I wanted to ask the community if there is a way within CUCM Administration (or any offshoot) to run a report where I can determine if VoIP phones are currently NOT using PoE but instead are utilizin...
Hi, Refer to below BoM would you kindly guide with the right license for 3rd party IP Phone to sync with the existing infra.? Call Manager Hardware 21.0BE6M-M4-K9=Cisco Business Edition 6000M Svr (M4), Export Restricted SWN/A121.0.1CON-SNT-BE6M4M4K...
In Cisco Unified CM Administration System version: 11.5.1.14900-11, is there a way to block unwanted, nuisance or harassing calls in call manager?
Hello, I Have Cisco Phone 8865 Software version : sip8845_65.10-3-2-16.loads, I try Monitor Cisco Phone with Program Wireshark. I see packet register with CUCM Active with Respond Status 200 OK, But Cisco Phone Request Register with CUCM Standby agai...
Hello, I Have Cisco Phone 8865 Software version : sip8845_65.10-3-2-16.loads, I try Monitor Cisco Phone with Program Wireshark. I see packet register with CUCM Active with Respond Status 200 OK, But Cisco Phone Request Register with CUCM Standby agai...
I have a Cisco CP-8865, Software version sip8845_65.10-3-2-16.loads. Cisco IP Phone 8865 have a problem keypad delay When press number for dial. Can you please solve this problem. Thank you.
Hi, I have a Cisco CP-7821 model POE IP phone, I wanted to use that phone to get registered with SIP.I have performed the following steps for that1) Downloaded the latest Cisco IP Phone Firmware sip78xx.11-5-1-182) Downloaded third Party TFTP Server ...
Forwarded calls shows "Forwarded" instead of the display name for newly configured phones after upgrading the cucm from 10.5 to 11.5. CUMC version 11.5Call type internalPhone type 7945 Its working fine for existing phones with the same version of fir...
Hi, I would like some help trying to force my CISCO 7965G and 9971 devices to use the G711 codecs, in the configuration file I did not find a TAG with this option.
Hi guys, so we tried to load a later IOS firmware onto our 2900 router from c2900-universalk9-mz.SPA.151-3.T1.binto c2900-universalk9-mz.SPA.154-3.M1.bin by upgrading it via Cisco Prime. Due to space Prime appeared to have deleted some files from fla...
Hello, I am hoping to get assistance on how to properly install a device pack to support the webex room kit mini. I already tried to install the latest device pack that would allow the mini to register on my call manager but it failed. I noticed that...
Hi all, I'm having some problems dialing from a third party SIP device. We have CUCM 10.5 on our campus. The device is a JK Audio AutoHybrid IP2 that has two extensions assigned to it. I had previously programmed one of these devices and it worked ...
We have a CUCM 12 cluster with a few subscribers. When phones are registered to a certain subscriber the DTMF on outbound calls does not work. If we update the CMG on their device pool so the phone registration moves to a different subscriber the DTM...
Would appreciated that anyone could give me some help on this.I had a MLS service hook to Cisco 2900 router and connected to CUCM. I'm trying to create a lab and referring one of the DID numbers from the MLS services connected to CUCM and route it to...
Good afternoon, I have been tasked with creating a help desk phone answering system... Customers will call one outside number and then be able to choose different locations... Press 1 for east, press two for west, press three for south.... Each locat...
