HI, I have Firepower (FTD) in HA managed through a standalone FMC, There is a peculiar issue, Whenever my Primary unit is active and I deploy , I get the error " Deployment failed due to communication Error", So I have to switch over to secondary u...
Forum Posts
Resolved! Cisco ISE restore backup
Hello Guys!I have a question about Cisco ISE restore from backup file. I don't understand the option "include ADE-OS". In documentation I found: Option: include-adeosDescription: (Optional, applicable only for configuration backup) Enter this comman...
Dear All,I have a standalone FMC managing 2 FTDs in HA, Recently I observed that Primary unit is showing disabled and secondary take on as active. During trouble shooting,It is found that I could not ping Manager(FMC) from primary unit [FTD]I could s...
Hi, Our monitoring is showing MEMPOOL_HEAPCACHE_0 2% freeCan anybody explain to me what it means and how i can fix the issue: sh verCisco Adaptive Security Appliance Software Version 9.8(4)25 Firepower Extensible Operating System Version 2.2(2.124) D...
Our ASA [ver. 9.10(1)] does multicast routing and the source is directly connected on inside. Every once in awhile a multicast stream (group) does not get forwarded to the RP (outside) and is dropped (show mfib ), and stays dropped. Performing a clea...
Hi all, i'm looking for some clarification. We have two firepower 1120 which we want to deploy in HA active/standby configuration.I have been reading up on my options around interface redundancy, and as far as I can tell we cannot operate with redun...
Hi, I have Firepower [FTD] in HA, Both the Firepower devices are connected to Nexus (93180 FX).I have configured BGP between Switches and and Firepower,While doing Firepower switchover or switch failover ( Shutting down on switch] , we observed that...
HI,It's taking long time in active/standby FTD switchover,Is there any mechanism to minimize the fail-over time or is there any config required? Primary Unit to Secondary unit - it takes 5-6 seconds Secondary Unit to Primary unit - it takes 10-11 se...
Resolved! CDO and device certificate
Hello, I am trying to onboard an ASA device in CDO. I get the errorCertificate could not be retrieved for IPADDRESS:PORT To which certificate it refers to?How could I change it?
Hi FMC/FTDI.m looking at creating an object for EOIP protocol (97)when I go to add new port object I select other tab and can see ETHERIP(97) is this correct and is it safe to do this, its to allow a capwap tunnel through. Thanks
HI, I am not able to deploy policies from FMC , have tried in many ways but issue remains unresolved, I am planning to Reset the FMC to facory default setting and start the fresh configurations, Pls let me know the process to do the same I have two ...
Hello everyone, I need some help with licencing. My smart licence is expired. I'm trying to configure ASA but I can't do anything without 3DES/AES alghorythm. So, I have read how to enable it and in order to that I need to generate token. I have gene...
Dear all,I have a network which in this Netwrok my FTD isnt connected to internet because of some security issues. As far as I know, to use AMP, our FTD has to be connected to Cisco cloud. In this scenario, my FTD isnt connected to cloud and the rule...
I have a very basic question. We have a Cisco ASA 5505 in our personal office. It limits the bandwidth to only 100 Mbps. Our internet is 300 Mbps so we're not getting the full functionality of our internet. We want to upgrade the 5505, but not sure w...
Hello all, Our offices are mpls connected and some of them have also local internet with FTD devices.I am trying to create a full mesh topology on these offices as a backup, in case we lose mpls connection. All of our FTDs are connected and managed b...
