I would like to see if there is any document which has the cons of ssl inspection of firepower module. Like the effect on resource usage like memory, processing power on the firewall
Forum Posts
Resolved! Is AES-256-CBC the same as AES-256-SHA?
Trying to VPN peer an ASA 5505 to a 3rd party's Palo Alto. The only IKE/IPSec options they have are CBC and GCM. Are either of those the same as the AES256-SHA that the ASA's support or am I out of luck?
Hello, Our ISP has given us Netflow access and we can see what the ISP Cisco router is sending and receiving, this is great but as a source or destination I only see our 'outside' public IP. I understand this is normal, but is there a way I can see w...
Hello!We are constantly confronted with the lack of memory on the our ASA 5515-x, resulting in failure of the device.Currently it has 8gb, of which only 4gb are available.Is there any possibility to add or replace memory to ASA 5515-x?
I have a problem with Firepower on ASA and Mozilla FF. When I start the browser and open any https website for the first time, I got the message SEC_ERROR_BAD_SIGNATURE when I reload this site everthing is fine. With Safari it´s the same behavior. Wh...
Hello, I would like to know how you guys order and design the FMC Access Control Rules? Sadly the FMC is not really optimized for a lot of rules, compared to the ASDM or FortiNet etc.. Its really painful in my opinion. Currently I've went with ...
Resolved! FTD 6.2.3.2, Whats App connection delay
Hello All, One of our folks pointed out an issue that I had never noticed (or paid much attention to) before. When opening the Whats App application on an iPhone, there is a delay of 30-45 seconds before the app finishes connecting on our network....
Hello all, I'm replacing a Juniper SRX650 firewall with a ASA-5516. The Juniper is configured for transparent mode, very simply sitting between my inside network and our service provider. No other connections besides the management interface. I ...
Is it necessary to use Firepower Management Center (FMC) to setup site-to-site VPN or RA-VPN? I am currently using the on-box FDM-system and FTD/system support diagnostic-cli. I find it hard to troubleshoot, reading logs etc. Do I really need to bu...
Hello, I'm stuck and don't know where to start. I Have an Cisco ASA5506X with 4 VLAN's with different security levels. VLAN 10 192.168.230.x/24 Security level 100 VLAN 2 192.168.2.x/24 Security level 70 VLAN 3 192.168.3.x/24 Security level 50 In ...
My company purchased some Cisco 2110 runing firepower threat defence v6.2.3 OS. As I work remotely got someone to patch the new Cisco 2110 to Lab PC console port as well as 2110 ethernet 1/2 (inside interface) to a lab switch port that I can route to...
I have found cisco's config for dynamic DNS on an ASA. However, I have seen many articles that the ASA doesnt support the HTTP update method that most dynamic dns services use.Does anybody know of a reputable ddns service? Also, can you lend a samp...
can i have on this attached network picture how to configure vpn site to site from remote location to main headoffice location in remote location i have Firewall/router: Make/Model/OS Cisco ASA5516-X in HO location they have Firewall/router:...
When add a FTD to FMC, the heartbeat somehow interrupted, then the registration process is staying in pending on FMC. seems in this situation, this registration process cannot be stopped or removed from FMC GUI. have tried the following steps: 1. rem...
I am not able to ping my ASA interface Fa0/0 which have assigned IP address is 192.168.3.2 My topology contains 2 VLANs with the configuration mentioned below:ciscoasa(config) # int gi0/0ciscoasa(config-if)# no shutdownciscoasa(config-if)# ip address...
| User | Count |
|---|---|
| 10 | |
| 10 | |
| 7 | |
| 5 | |
| 3 |
