hello, i have connect two data centers with 2x16G FC and 3x10GE. what Cisco DWDM solution do you suggest?
hello, i have connect two data centers with 2x16G FC and 3x10GE. what Cisco DWDM solution do you suggest?
We are about to redo our stand alone wireless with WLC's and LWAPP's. As part of the process we are implementing ISE and were going to implement the Wireless Control Station, but it has morphed into a wired/wireless all encompassing solution called C...
The module is shown to be rated at 400G. The 2x100 in the part number would lead you to believe it is only rated for 200G. Is this truly a 400G Transceiver? With an MPO24 Interface how does it achieve 400G over 10 TX Lanes?
Hello. I have been having issues with this one interface GI2/0/4 on L3 Cisco 3850 switch that's been throwing out lots of Rx power low alarm; Operating value -26.7 dBm; Threshold value: -21.0 dbm logs. My senior tech and myself have already troublesh...
Dear community. I am stuck up on the SFP issue. I have Cisco SFP-H10GB-CU3M.When I am trying to connect something to a 10g port with these SFP, it is not working at all. But when I connect other devices with these SFPs everything works fine. I can se...
Does this point to an issue with an SFP? We have a 4500-x vss stack, through which runs the heartbeat for a bunch of vrrp groups upstream, both routers have been going active due to loss of heartbeat. One of the switch uplinks has a tx power of -10db...
I connected a 40GBASE-CR4 Passive Copper Cable, 1m cable between 2 x C9500-24Y4C-E switches, but I don't get a connection. Is there something I am missing?
should i count together with input and output rate for measuring Total load of Wan interface?Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL------------------------------------------------------------------------* GigabitEthernet0/0 0 0 0 0 198070...
Good evening folks, question for you:Am I crazy, or does Cisco not have a 10G LC mm SFP that that can also be adjusted to handle 1Gb/100Mb/etc. ?We have a large project at work that is fully 10G LC fiber; however, we want the capability to connect to...
Hi, I'm working in a networking project and we are evaluating using the Catalyst high performance C9500-48Y4C and C9500-24Y4C as distribution switches.For a short time we need to have the down-links in 1G and then we will migrate them to 10G. I would...
ASR 9001, with 5 satellites 9000v2 This command works for the MPA-module inside the router.RP/0/RSP0/CPU0:router#sh controllers gigabitEthernet 0/0/0/* phy | i "interface:|Tx Power:|Rx Power:|Xcvr Code:"PHY data for interface: GigabitEthernet0/0/0/0X...
What is the added intelligence in routed optics? Does it repair the network's data transmission capabilities (originally at layer 2) by itself? Is there a missing layer 2?I am struggling to understand the "routed" aspect of optics. If you could pleas...
HelloI need to cut down on our cabling expenses especially performing due diligence on factory blds regards cabling specifications which have not been updated for some sometime, Any suggestions towards a good quality mid range proven fibre tester (OM...
Does the Cisco X2-10GB-SR and Cisco X2-10GB-LR modules installed into a WS-X6708-10G-3C module installed in a Cisco 6504 support both 10Gb and 1Gb speeds?
I was told by a site, due to OSHA - that I will need to provide my own Optical Laser safe glasses. I have no clue what to buy, due to the latter, I am looking for recommendations. Will be working with Single-Mode fiber and some runs are really long -...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-05-2024 05:19 AM | ||
03-27-2024 12:16 AM | ||
03-27-2024 12:09 AM | ||
09-10-2023 08:07 AM | ||
08-03-2023 03:20 AM |