Hi Team, All Static route BFDs connected to core device are flapping intermittently. I did not see any error logs for the same. only show bfd neighbors details the uptime is showing some hours. Please help me to identify the root cause. Find the atta...
Forum Posts
Hi, I want to configure IP Sec crypto isakmp on router P2P link interface which is connected to the firewall for secure traffic & data. I want allow selected IP address & subnet on this interface
Can someone please help me figure out why I can't ping from my Azure VM to any on-premises devices? I've added exclusions for ICMP in Windows Firewalls on both sides and can successfully ping from on-prem (i.e. 192.168.1.90) to an Azure VM (i.e. 10.0...
So i have set up a 881 and i can ping out but not sourced from vl1 ive added ip nat outside to wan int fa4 ip nat inside on vl1 with the overload acl 10 permit 192.168.1.0 /24 added ip route 0.0.0.0 0.0.0.0 fa4 yet i cant reach out from beyond the ro...
We bought and ISR 4331 performance license and using PAK i converted it to .Lic file but while creating license file i entered wrong UDI, means one word was left in coping it, now when i apply this license it is showing error that UDI does not match....
Hello. This is my first post to the Cisco Community. Please be gentle if I make any mistakes. I'm in dire straits and really hoping you all could be so kind as to share some of your knowledge with me. I recently started working for a municipal entity...
I'll try to keep this brief. If you need any additional information, let me know. Basically, we have a 56K connection to one of our remote sites (it's all that's available). We recently purchased a new 2911 router and are consolidating a couple of ...
Dears, I have a cisco 887 router and I have tested on two different DSL line. The first line it worked fine with while the other noe is not. both line on same exchange and establishing the ppp session with same BRAS. The debug seems that there Establ...
Hello,on top of our DMVPN config we have created an additional VRF on a Cisco 881 [15.4(3)M8] which is a second internet connection meant for voice services. Between the LAN VRF and the new additional voice VRF we`ve created a direct physical connect...
I have 3750E with c3750e-universalk9-mz.122-50.SE3 IOS. I have two redundant Links to different ISPs with equal Cost. G0/1 and G0/2, both are advertised in ospf within same area with equal cost. I have snmp enable traps and my snmp is connected in a ...
Resolved! Cisco 4300 ISR IOS upgrade issues
Hello, I have a cisco 4331 router where I need to upgrade OS to higher version. Current version: #sh version Cisco IOS XE Software, Version 16.06.02 I have OS for version16.6.3 in the bootflash and have changed the boot marker but when I reload the...
I am wondering how to block routes that get redistributed from EIGRP into BGP. I have a 3850 advertising local networks via EIGRP to a 4331 router (MPLS) and these are then redistributed into BGP so they can be routed across my MPLS circuit. The issu...
Team, This question is on license for the new Cisco 4xxx routers. How can I check is the CiscoONE license is installed on the router? When I do a show license it shows me below features: Index 1 Feature: appxk9Index 2 Feature: uck9Index 3 Feature: se...
For some reason I am trying to type above command but it seems not to recognize the command. Any help will be appreciated.
Hi All, I need some help please, we have a client with a telco PRI, the telco had a failure last week but has since resolved but ever since then when we make an outbound call, the call lasts for about 2-3 seconds and then shuts itself down(inbound ...
