On a router with multiple interfaces using DHCP to get its IP address. Is there a more direct way to find out which default-gateway (next-hop IP) is assigned to which interface? I have tried the "show dhcp lease" command but it does not give the de...
Forum Posts
If R1 and R2 are in the same Ethernet link, according to the following exhibit, R1 should be DR. However, the exhibit mentions different DR in each router. Isn't there supposed to be one DR per link?
Hi all,Please help me on this.We have a Cisco router in our network. We have configured many port forwarding in the router and all are working fine. One of my application is forwarded to the port 8080 from outside to inside. We can access that appli...
Dear Friend, I am facing issue to configuring ITD in nexus 9504 switch as i am getting below error N9K-CORE-SW01# sh itd ITD-N9K statisticsERROR: Cannot get pbr statistics data, please enable ITD statistics. While i have already enable below fe...
Resolved! IPTV with Cisco 4507R multicast issue!!!
Dear All, I want to implement Otrum IPTV, which works on multicast. I have cisco 4507R as core switch, whenever i enable multicast (dense mode) the cpu usage goes upto 60% for ever on core switch.Does anyone has integrate IPTV to cisco 450...
Good Day everybody, i'm glad to joined to this community, Right now i have a conflict, because we have the Router provide for the Internet Company, on a store, it is connected to a generic switch in a small kiosk by Ethernet, which is connected to ...
Resolved! BGP Redistribution
Hello Everyone! i am self studying and stuck here please help me out on this.In my topology i have three Autonomous systems of BGP. Here is what i have done.-Each AS is runnin OSPF internally.- R3, R4, R6 and R7 are participating in IBGP/EBGP while R...
Resolved! Cisco Router login Problem
Hi friends in cisco 2911 series router. i cant able to login in one of the router interface GigabitEthernet0/0 we have configured service provider wan IP address in Gigabit Ethernet 0/0 and in Gigabit Ethernet 0/1 we connected wan interface for our f...
Hi All I have a 998VA router and I need to access the internet from the inside network as well as provide a site to site tunnel to the office. LAN side subnet is 192.168.1.0/24 Remote office subnet is 192.168.2.0/24 I need a site to site vpn to flow ...
TopologyI have a data centre with two layer 3 distribution switches using eigrp to connect to two edge layer 3 switches which are running eigrp and bgp. The two edge switches communicate with each other via ibgp using their loopback addresses which a...
Hello, I am facing some issue in Routing, kindly help me figure it out. thanks in advance. I have multiple routes into my cisco 2900 series router i.e. 0.0.0.0 0.0.0.0 192.168.200.1 (towards my firewall for accessing internet) 192.168.15.0...
The Cisco C897VAG-LTE-LA-K9 router uses an AC adapter with a 12 VDC connection into the router. Can one use a separate 12 VDC power supply to power the router or is there any active circuitry that needs to see the genuine Cisco AC adapter? Also do...
Hi, I'm planning to limit a certain bandwidth base on my client subscribed eg. 2Mbps, 10mbps, 5Mbps, The problem is i dont like to use rate limit from my router since it will drop excess traffic, and traffic shaping will do only on outbound int...
In reading the design guide for bgp path diversity with a shadow RR it highlights the need to configure bgp bestpath igp-metric ignore on all RRs if they are not "collocated." My question is, if the shadow RR is receiving an advertisement that is c...
I am wanting to upgrade to a ASR-9010 from a ASR-9006-AC-TR. Can you use the RSP440's, the MOD160's, and the line cards in the ASR-9010. This is what I have in my ASR-9006 that want use in a new ASR-9010 chassis. Can this be done A9K-RSP440-TR(...
