Hello, I have set up a lab of 3 physical routers. trying to create a serial connection using crossover cable via the dsu/csu. I gave them ips and they are in the same subnet and no shut was issue but they are not up. Please tell me what Im doing ...
Hello, I have set up a lab of 3 physical routers. trying to create a serial connection using crossover cable via the dsu/csu. I gave them ips and they are in the same subnet and no shut was issue but they are not up. Please tell me what Im doing ...
Got a customer whose Fibre Access has been taken down, the Fibre Access Terminal they are off has been destroyed (suspect by a drink driver again). Is it possible to install a 3G/4G card in these or will we need to put an external 4G on the backup WA...
Hello there, On nexus 3064 I can do Q-in-Q with following config: nterface g0/10 switchport switchport mode dot1q-tunnel switchport access vlan 222 but I don't know how to do many Q-in-Q incoming tunnels on one interface. I receive VLAN 800-811 in...
Hello, I have a strange problem with MSDP perring on my 3560 box, in logs i see: 059846: Dec 11 14:27:10.156 MSK/MSD: %MSDP-5-PEER_UPDOWN: Session to peer 192.168.1.1 going down059847: Dec 11 14:27:23.091 MSK/MSD: %MSDP-5-PEER_UPDOWN: Session to pe...
Hi team Looking at placement of PIM SSM blue line here. Using a GRE Tunnel to enable Multicast between WAN routers due to the wider WAN cloud not supporting Multicast. New to PIM SSM so is it in the correct place? Assisting with drawings for IPT...
Hi Guys,Have an ASR1006 (Dual RP's/Dual ESP's), and the "standby" RP is stuck in rommon:System Bootstrap, Version 12.2(33r)XN2, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com/techsupportCopyright (c) 2008 by cisco Systems, Inc.Current ...
When is the C1100-8 coming off of NPH?
Good morning, We have recently upgraded our MPLS circuit from 21MB to 100MB through our CO. This circuit supports multiple sites in outlying areas controlled through QOS depending on the circuit bandwidth at each site. One of the external sites ...
Hi Is there something wrong with this config to prepend a default route? I've tried this: router bgp 64521 network 0.0.0.0 route-map DEFAULT_COMMUNITY !route-map DEFAULT_COMMUNITY permit 10 match ip address prefix-list DEFAULT_ROUTE set origin i...
Hello all, I have something that seems pretty straightforward that I'm trying to emulate. I'm trying to assign a DHCP address to a spoke tunnel interface on a DMVPN setup. I have the DHCP server on a separate router (172.16.0.3) and the hub acting ...
Hi there, I have a topology that I have an ISR that connects to two ASRs. The two ASRs connect to a FW. between ISR and ASRs they are EIGRP and between ASRs and the FW it is BGP. I do redistribution on the ASRs between EIGRP and BGP. The problem ...
I am trying to configure failover with a gateway of last resort. I have 2 routers and each have there own ISP connection. One is our primary, and the other is our backup that also routes all of our wireless traffic. We have route-maps setup on the co...
Hi all,We have a few Cisco 2911's running 15.0(1r)M15. We have Brocade FCX648S's and a TurboIron 24X that were just deployed - they will have VoIP phones connected to them. The folks at Brocade have said that they just need the command "trust dscp"...
When Ebgp & Ospf is configured on router and we have to ospf route should prefer rather than ebgp route???
Hi, i'm new at cisco devices. I recently install a router rv325 with vlans. All the vlans can access internet without problem. But through the router, i can't access some website. I am not sure but i think it is a problem with the used port. For exam...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-03-2024 01:45 PM | ||
05-03-2024 10:57 AM | ||
05-03-2024 10:28 AM | ||
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM |
User | Count |
---|---|
14 | |
7 | |
4 | |
2 | |
2 |