I have a Cisco 3750 switch in my network. Previous administrative did not share the configuration backup neither credentials to login into the device. Also I am not sure whether configuration was saved in the startup config. Is there any way where I...
Forum Posts
Resolved! Marking CoS in both tags in QinQ
Hi, We are designed a new service based on a FTTH indirect access. Our provider delivers each connection using QinQ. There are two connections types: best efford and gold. In gold connections we need mark packets with a CoS=3 in both tags. We are usi...
Resolved! ICMP Problemm
Hello Friends, In my enteprise enviroment I have Cisco 1900 series router wchich is connected to ISP with Gi0/0 and with Gi0/1 to Barracuda NG Firewall F380. Barracuda is connected to HP procurve L3 switch, on wchich Vlans are terminated. Between Cis...
Resolved! Configuring Cisco 1801 router for PPPoE
Hi,we have cisco 1801 router and want to configure for PPPoE.As our ISP has provided adsl connection having following settings:Encapsulation: PPPoEMultiplexing: LLC basedVPI = 0VCI = 103Login =xxxxxPassword =xxxxxIP: dynamically from ISPI am new t...
Hello everyone! So I was recently informed we will be migrating from an At&t IPFLEX network to a new ASE network. We have 16 locations which are stub networks all pointing back to the corporate location. Normally this wouldn't be a big deal except ...
Hello everyone! I'm new to the forums, so I'm in your care :) I'm in a bit of a pinch, you see, I'm trying to get a network working with only IPv6, thus far I've been able to give everything their respective IPv6 addresses but I can't seem communic...
Hello, Two sites are connected to L3 MPLS with different AS#. We are doing eBGP with the provider and doing OSPF redistribution from BGP on the backend. There is also dark fiber between the two sites that is used as a backdoor link. I would like...
Resolved! Traceroute and Request time out
Why do i receive request time out in the middle of a traceroute.. what does that means
Resolved! Traffic shaping per client on ISR 4331
Hi all We have a 100Mbps Internet link, feeded by 4 proxy nodes. The proxies are accessed by around 800 users. The point is now I only have four IP addresses as the sources which pass the router. But as every single user creates one or more session...
Hi Experts, I am very curious to find out , how Cisco Adaptive Qos intelligently finds out the Varyiying bandwidth on the DMVPN Spokes. I know how to configure adaptive qos and set ratio , but what i dont understand on what what factors or how ci...
Hi everyone, I am reaching out to get your opinion on my below config, What i want to achieve is that a spoke having two vrf and two tunnels pointing to two different hubs, two eigrp instances with different AS numbers. Spoke will have two differne...
Hello, we have recently installed an ASR1001X running asr1001x-universalk9.03.16.02.S.155-3.S2-ext.SPA.bin. What we noticed is that the access-lists used for QoS do not show counters, even though traffic seems to be matched when running show policy-m...
The main office site to a single remote site (warehouse) is working well with two RV130W VPN routers. Now I have a second remote site. I copied the warehouse configuration to the new RV130W and changed the pertinent addresses - static, gateway, a...
Hi, I cant find any explantion on internet, why there are routes which has no Cidr on "show ip bgp regexp ^xxxx$" *> 2xx.xx.2x9.0 2xx.xx.x9.6x 100 0 12345 i <<<<<<<<<<<<<<< no cidr*> 2xx.xx.3x.0/19...
Resolved! configuring pppoe on cisco isr 4331
i have a 4331 on my network and i want to connect to the internet via PPPoE over ethernet how can i achieve that? i tried connecting using vpdn but in vpdn-group i cannot request dialout
| User | Count |
|---|---|
| 14 | |
| 6 | |
| 3 | |
| 2 | |
| 2 |
