I have two devices with OSPF but the connecovity it is going to the secondary decive and we need it in the primary.
Can we do something similar as clear ip bgp * soft for OSPF?
I have BGP Multihomed routers. Everything works fine and outbound traffic is being determined via the BGP protocol. Router A ISP is 50Mbs and Router B ISP is 100Mbs. Traffic goes out both routers as it should. I have a specific destination IP (say ...
Hello,
I want to make multiple SSID and want them all to have different network addresses. So all of them have different ip address ranges they give to the devices connected to them. Do I need to make a DHCP pool for each vlan assigned to an SSID?
th...
I jus updated my Cisco Switch 4500 cat4500e-universal.SPA.03.06.06.E.152-2.E6.bin
but is not letting me setup SSH
Also tried with telnet but no success
What else can I do?
Hi,
If 2 seperate router's connected over P2P link towards wan both making use of EIGRP routing protocol and both having same bandwidth and delay metrics, will the traffic comming from Lan load share between both the router's ???
Both the router's ...
Hi
I have this:
BOOT variable = bootflash:cat4500e-universalk9.SPA.03.04.00.SG.151-2.SG.bin,1;bootflash:cat4500e-universal.SPA.03.06.06.E.152-2.E6.bin,1;CONFIG_FILE variable does not existBOOTLDR variable does not existConfiguration register is 0x2...
So we have two 500Mbps circuits that are both /27's from our ISPs and they are both setup the same as follows:
1. cable from the ISP router goes to a 2960x, 2960x has no config on port from ISP
2. 2960x port with no config goes to an Ecessa Powerli...
I am trying to config a 2620 Cisco router to perform subintreface (F0/0.1) for Vlan Trunk Protocol, however when I try to configure the encapsulation dot1q, I continue to receive error massage with ^ symbol below the 'c' See below, the platform ...
Attempting to setup the following site.
Remote site --- C3750E --- RV325 --- VPN/Internet --- ASA --- corporate network
The RV325 is configured in router mode.
On LAN it has a 30 bit subnet configured that is connected to the C3750E.
Able to ping f...
Hello! I am trying to redistribute EIGRP routes into OSPF. Everything is working fine. However, I am redistributing them into area 0. My question is "Should they be?".
My initial plan was to have a separate area to bring the EIGRP routes into. ...
Hello Everyone,
My customer ordered an access circuit for their MPLS service but the local telco delivered the circuit as fiber and they are out of stock for a media converter (it will take them 2 months or so to get one!) that would have allowed t...
Hi
I have a Nexus C93108TC-EX switch.
Software BIOS: version 07.59 NXOS: version 7.0(3)I4(5) BIOS compile time: 08/26/2016 NXOS image file is: bootflash:///nxos.7.0.3.I4.5.bin NXOS compile time: 12/23/2016 16:00:00 [12/24/2016 01:37:34]
In each QSF...
I have an ASR9K pair running BGP with a provider. The provider will send only a BGP default route. The ASR9K pair run HSRP. Is it possible to have the HSRP track the presence of the BGP default and reduce priority in its absence? The ASR9Ks will also...
HI All,
I have some network experience, which is mainly L2. I have a BT Business broadband line and I would like to use a 3750 L3 switch to create multiple vlans with the routing and use the BT line as the internet connection with the default route ...
I can match rtp traffic in a class-map in two different ways:
class-map match-any CMP-VOIP match ip rtp 16384 16383
and
class-map match-any CMP-VOIP match application rtp
Is there any difference between them? Is one better than the other?
Does both a...
