I am trying factory reset a Cisco C8200L-1N-4T Catalyst Edge router and unable to find a reset button on the device. Can I please get some help with any documentation or instructions to reset it?Thank you
Forum Posts
Hello everyone,I have a routing scenario with eBGP and EIGRP. I have an SDWAN appliance and a Cisco 4451 router both learn the same routes from the WAN with the SDWAN appliance connects to the Nexus 9k and exchange route via eBGP and the Cisco router...
Resolved! No internet behind FTD
Hi,i have this setup. Router -> FTD -> Switch -> PC.Router sample config:interface GigabitEthernet0/0/0description ISP1ip address dhcpip nat outsidemedia-type rj45negotiation autono cdp enable!interface GigabitEthernet0/1/0!interface GigabitEthernet0...
Resolved! Taging an EIGRP route
Hi all im trying to tag an EIGRP route thats incoming - but for some reason i cant get it to tag - i must be missing somthing : router eigrp BALLS!address-family ipv4 unicast autonomous-system 10!topology basedistribute-list route-map nut inexit-af-...
Hello allI am a learner. I have combined two standard Cisco PT exercises that i have completed and I have tried something extra. I have linked R3 and ACME1. ACME 1 is using running BGP/OSFP and R3 OSPF. The running configurations are below. I can't ...
Resolved! Cannot ping switch from other network
Hello guys. I have create a topology on GNS3 and i have a problem, i cant ping my switces from end devices. All the network decives is assigned to the 150 vlan, i have enable ROS on the router for all the vlans. I can ping the switch (192.168.150.7) ...
Resolved! Access a server inside LAN
Hi,I am facing an issue with my LAN, I have a router Cisco 1921 and behind a switch Catalyst 1000, on one of the ports of the switch I have a little server with proxmox on it for virtualization, I would like to access it from anywhere in the internet...
After updating the firmware to version 16.12.07 (from version 16.06.04), the translation rules for the ip address pool stopped working.Static rules work and 1:1 rules work. I don't know how to solve the problem, an example of a broken rule:ip access-...
Hello, I'm in CALO San Jose Lab...attempting to bring up GLC-2BX-D transceivers btb on a WS-X4640-CSFP-E card with a C4506-E chassis. I'm also using a WS-X45-SUPL-E Sup card on that chassis.How do you configure these transceivers on th ports? I'm al...
Hi folks, Hope someone can help me out here... So far I don't see any mentioning of Security license (as in the ISR4K) being mentioned in the Catalyst C8200 documents. Only hsec is being mentioned. Is the security license not applicable on the C820...
Disclaimer: at first I thought this was merely a question about the title, but I realised it's many questions. I'm sorry if this caused the post to be confusing. In an attempt to improve the situation, I include a short question list at the end. I ...
Can anyone advise how to best troubleshoot slow dns issues? Are there any helpful tools? When slow dns occurs the problem is sometimes very elusive and not obvious and may take hours before you finally realize the cause.
I have router 2921 with 3 layer 3 interfaces i need to configure one of them as access interface encapsulation in bidirectional (not subinterface solutions)
hi all , im trying to configure ipsec tunnel from R2 to R4 (top right router) . but after i configured all the ipsec gre commands , my ospf routing seems to be down suddenly and now both my ipsec and ospf doesn't work. any one can help me please? i'm...
I am facing issue downloading Cisco router 3900 series IOS, I click on download and it send me to another webpage, it keeps redirecting me in a loop and I get stuck there, if anyone knows why is this happening, Thank you!
