Hello,I am trying to get the internal access point in a 1941W to work. I didn't have the original configuration, so I reset the configuration on the 1941W and got that going. For the internal access point, when I connect to the console and try to l...
Forum Posts
Looking to upgrade to FPR2120-NGFW-K9 firewalls for multiple locations but we're not clear if FQDN routing is an additional license or requires purchasing other things? Can anyone confirm the FPR2000 series will perform FQDN routing “out of the box”?...
Resolved! Fully specified static route error
In PacketTracer I'm trying to configure a fully specified static route. All interfaces on the routers are Ethernet and are interconnected with straight cables. The router model is 4331. When entering the route in the router CLI ip route 10.10.10.0 25...
Hello,I am struggling to configure the Topology attached bellow and I struggle to obtain full connectivity, to be more exact, I have encountered a behavior, where:R3 Routing table does not include route to 1.1.1.1/32R2 Routing table does not include ...
Hello, I have an assignment where I have to route 3 routers that uses VLSM with RIPv2, ive assigned all the IPs needed to the pc and router, but I can't route with RIP for example, when I try using RIP in router 2 and typed 198.66.66.160, it converte...
Hi everyoneI have a 4331 that was rescued from an upgrade process on a local datacenter, and they say it was working before removing it from production.I now have a problem with it, not being able to boot it up no matter what I try.It gives me the fo...
hi,i got a new 4k router with IOS-XE 17.3.x and would like to "downgrade" to our standard code 16.12.xboth code have smart license enabled. i haven't registered the 4k to smart license server/CSSM.my question is, is it "safe" to downgrade? or will th...
Hi, How to you route "same subnet" with "different vlan". My teacher wants us to makePC1- Vlan 53, Ip:192.168.53.11, subnet /24Switch-Manage Vlan 55, Ip:192.168.53.55, subnet /24I read this document but they are on different subnets.https://www.c...
Hello, I have router 1111 and Switch 1000, between them is trunk with 5 VLANs, default gateways sitting on the router. Just two VLANs have Internet access (VLAN 10 - via VPN to core router, and VLAN 99 local NAT) - Switch has default gateway comman...
Resolved! Distribute Static Routing
HI..If we have several static routing, can we distribute this static routing to OSFP or EIGRP? So all router will using same path to reach the specific destination?
I have a 1941 that has high CPU load from interrupts with no traffic. I started out with a clean configuration and it is running IOS 15.8(3)M7. It has about 89% CPU usage even without traffic, but it's almost all interrupt. It has a very simple co...
Hi to all,Is it possible to redistribute a default route using ospf multiarea just in one area??For example if i have my area 0 for backbone and my area 1 for my locations can I redistribute a default route just to the area 1????Thanks in advance
Hello! I'm having trouble pinging the inside of routers and connecting to the web server. I can ping the loopback address 20.0.0.1 from all the devices. When I run in simulation mode and ping 192.168.1.1 from Server0, the packet reaches the server, b...
Resolved! Little confusion about Routing
Hello, i'm new'ich to networking, can somebody please tell what is it meant by saying that à router separates LANs(1) when, by default, when i set up two LANs physically connected to the same Router the machines respond to other LAN's machines's ping...
i setup an ipsec between a ciso router and a fortigate firewall.Tunnel is up in both device while the two LAN subnets are unable to ping each other.i saw lot of articles and tuto and sounds confused about the necessity of NAT on cisco side!!!!!!pleas...
