trying to get loopback addresses to advertise *Mar 1 00:44:04.715: %SYS-5-CONFIG_I: Configured from console by consoleR2#conf tEnter configuration commands, one per line. End with CNTL/Z.R2(config)#router bgp 500R2(config-router)#network 192.16...
Trying to switch my source from R12's F0/0 interface to its L0 interface interface FastEthernet0/0ip address 10.1.3.12 255.255.255.0duplex autospeed autointerface Loopback0ip address 12.1.1.1 255.255.255.224exitrouter bgp 1000bgp log-neighbor-...
Hello I have done best I can in terms of research on what Wildcards are but I just am not processing it.Do Wildcards work to create a range? For example, would 192.168.1.0 0.0.0.15 mean 192.168.1.1 - 192.168.1.15? I want to break up 1 Network onto 2 ...
i have two data center. sharing data with each other via isp ckt. Port channel coming from router has configure priority as well as ospf cost. I want to know what's the difference between priority and cost. Also, can we just use cost to make routing ...
Hello, Cisco community I am looking to configure Cisco 4321 router with Call Manager and pass the SIP traffic to Cisco IP phones. Has anyone done the configuration before? Any help would be much appreciated.
Hello I was wondering if it would be advisable to manually input my WAN default route as well as it being obtained. I ask because when it is obtained manually via PPPoE it does not show up in "static routes". Curious if I should also manually make ...
Hello -Looking for input on 4331 max IPsec throughput when boost & HSEC license installed We have a case where two locations (both with 4331's) are having internet WAN links updated to 1Gb. The only way to attempt to get the full throughput (general ...
Dear community i would like to use a command like this: copy http://ciscoiosimages.company.local/image123.bin flash:image123.bin vrf LAN I know there are things like: ip ftp source-interface Loopback0 ip tftp source-interface Loopback0 But there isnt...
I migrated configuration from ISR1921 to ISR4221, but find ip load-sharing per-packet command(used in ISR1921) is disable in ISR4221(CEF is enable), only ip load-sharing per-destination is enable by default.know load-sharing per-packet command is not...
my interface is in a specific VRF interface Loopbackx ip vrf forwarding MGMTxxxip address xxxxxxxxxx and the global comand ip tftp source-interface Loopbackx is also enable the problem is though I can ping to the ftp s...
Hey team, so I’m pretty new and I just built a home lab, 2x 2811, 2x 2960, 2x 3560, 2x 1841, and an ASA 5505. The issue on having is the Voip phones fully configuring. The phones will boot and it will pull the right default gateway and it will show...
I have planned to configure the snmpv3 from snmpv1 on cisco router cisco ASR1001-X. But I am new on this, so can anyone please provide me the script to configure the snmpv3 in cisco router asap,My solarwind server IP: 10.122.1.1 and It would be grea...
I want to separate my network, i have 2 vlans 10.76.0.0 and 172.16.0.0, I don't want them to be able to ping or communicate with each other. I am currently able to ping ex: computer 10.76.2.30 can ping 172.16.32.1, we need to separate them and not al...
Question in topic, I'm looking for 2 intermediate-advanced or lengthy prefix labs. It deosnt matter if it's mixed in with other protocols/coccepts, in fact it's welcome. Please post up Thank You
Hello Seniors, I am a beginner. I am doing a lab of OSPF but my routers interfaces are not getting up. I have run "No shut" on interfaces many times but it's not working. Please find below the packet tracer lab fine. Remember: all routers are in "Are...
