buenas tardes, requiero su apoyo para ver si tienen algun caso presentado con estos mensajes que presenta ese modelo de router y que ataca al plano de control porque se tiene varios eventos con cambios en el HSRP y process cpu elevado. los routers ti...
Forum Posts
Hi there, I have a question: Can the HSRP protocol be configured to work on two different router models (ISR4K and C8K)? Kind regards, Josue Gaytan
Resolved! EIGRP authentication issue
Hello guys, I have 2 routers that are connected to each other through interface G0/0. Before EIGRP authentication was configured, they could see each other as EIGRP neighbors. The moment I put in authentication on both routers' interfaces G0/0, the E...
Hi, We have a customer with a 4331 looking to increase bandwidth on their circuit we supply, and their router requires a boost licence to support the upgrade. When licence order was placed it was rejected because apparently the licencing is now End o...
HI All, we are configuring the IP SLA on Cisco Router,we have two Internet links and one router.I am able to reachable the internet from my PC via 2nd ISP, when I unplug the 2nd ISP cables, now the Primary static route is not showing, and the primary...
Resolved! Policy based routing issue
Doing a lab ~When applying an ACL to policy based routing it is working as intended. When applying a prefix-list that is supposed to be matching the same subnet it is not. R3 is applying PBR. R4 has two loopback:L4: 192.168.4.1/25L5: 192.168.4.128/...
Hi, I am currenlty working on packet tracer project for school regarding this information of a corporation "Across the States Bank (ASB) takes pride in providing our customers with superior service and the ability to manage their finances 24/7 from a...
I have set up a straightforward static 1:1 tunnel connecting two remote locations in a Hub and Spoke configuration. EIGRP is in operation between them. Recently, I've observed that the routes are disappearing and reappearing every hour or even minute...
Hi All,I am looking for command to configure SNMP version1 in Cisco N540x routerPlease message me it will help a lot.Regads,Prashanth
Looking for some description for one particular LED on the front panel of ir1101. The LED-icon is showing a human + LED. Documentation:https://www.cisco.com/c/en/us/td/docs/routers/access/1101/b_IR1101HIG/b_IR1101HIG_chapter_01.html#con_1200520 says ...
Resolved! Cisco: MPLS Supported Routers and CEF
Hello World, Can someone please clarify the following question, succinctly, without a philosophical diatribe:The chart I obtained from Cisco shows that only 7200, and a handful of others support MPLS, and must have CEF enabled. Then I began reading o...
Resolved! SVI - VTP no sync
Configuring c1921 with a couple SVI interfaces, yes the Switch neighbor willrecieve the IP defined from the scope that i give, and ping alive both side.VTP v2 Server setup c1921, and Switch running Client mode butno VTP synchronisation will be succee...
I had configured 2 P2P with RSTP protocol between two location primary one Fiber and secondary on RF which is backup P2P , it's successfully worked. But some time without any fiber outage or down traffic divert on RF P2P. Primary is 200mbps and Secon...
i signed in to a new ISR 1100 series router and get this message after the configuration finished installing and prompted to there a new password %Cisco-SDWAN-RP_0-CFGMGR-4-WARN-300005: R0/0: CFGMGR: New admin password not set yet, waiting for daemo...
On R1int vlan 2, ip add 10.1.1.1/30int fa0/0, switchport mode access, switchport access vlan 2On R2Int fa0/1Vrf-Testip add 10.1.1.2/30Can R1 and R2 ping each other?Does the vrf or the vlan takes precedence?
