Hello,
I'm reaching out regarding a configuration issue we're experiencing with our 2921 router and the 4 port Gigabit EtherSwitch EHWIC card installed. Despite our efforts, we haven't been able to successfully configure the card to allow connections for devices.
Specifically, we're aiming to set up the ports to utilize the existing DHCP addresses, although we're open to creating a new DHCP set if necessary. The primary requirement is for these ports to have internet access once configured.
Could you kindly provide guidance or step-by-step instructions on how to properly configure the Gigabit EtherSwitch EHWIC card to achieve this? Any assistance or resources you could offer would be greatly appreciated.
Thank you very much for your attention to this matter. Looking forward to your prompt response.
-Don
----------------------------------------------------------------------------------------------
Current configuration : 3272 bytes
!
! Last configuration change at 14:07:54 EDT Thu Apr 25 2024
!
version 15.4
service timestamps debug datetime msec
service timestamps log datetime msec
no aaa new-model
memory-size iomem 15
clock timezone EST -5 0
clock summer-time EDT recurring 1 Sun Mar 2:00 1 Sun Nov 2:00
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
ip dhcp pool LAN
network 192.168.2.0 255.255.255.0
default-router 192.168.2.1
dns-server 1.1.1.1 8.8.8.8
!
!
!
ip cef
no ipv6 cef
multilink bundle-name authenticated
!
!
!
cts logging verbose
!
!
license udi pid CISCO2921/K9 sn FJC1945A0KY
license accept end user agreement
license boot module c2900 technology-package datak9
!
!
!
redundancy
!
!
track 1 ip sla 1 reachability
!
track 2 ip sla 2 reachability
!
track 3 list threshold percentage
object 1
object 2
delay down 40 up 40
!
!
!
!
!
interface Embedded-Service-Engine0/0
ip address 192.168.30.1 255.255.255.0
shutdown
no mop enabled
!
interface GigabitEthernet0/0
description WAN1
ip dhcp client route track 3
ip address dhcp
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
no mop enabled
!
interface GigabitEthernet0/1
ip address dhcp
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
!
interface GigabitEthernet0/2
ip address 192.168.2.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
!
interface GigabitEthernet0/0/0
switchport access vlan 10
no ip address
!
interface GigabitEthernet0/0/1
no ip address
!
interface GigabitEthernet0/0/2
no ip address
!
interface GigabitEthernet0/0/3
no ip address
!
interface Vlan1
no ip address
!
!
ip local policy route-map PRI_ISP
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip nat inside source route-map NAT_ISP1 interface GigabitEthernet0/0 overload
ip nat inside source route-map NAT_ISP2 interface GigabitEthernet0/1 overload
ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0 dhcp
!
ip access-list extended NAT
permit ip 192.168.2.0 0.0.0.255 any
ip access-list extended RMAP_PRI_ISP
permit icmp any host 8.8.8.8
permit icmp any host 4.2.2.2
!
ip sla 1
icmp-echo 8.8.8.8 source-interface GigabitEthernet0/0
frequency 10
ip sla schedule 1 life forever start-time now
ip sla 2
icmp-echo 4.2.2.2 source-interface GigabitEthernet0/0
frequency 10
ip sla schedule 2 life forever start-time now
dialer-list 1 protocol ip permit
!
route-map PRI_ISP permit 10
match ip address RMAP_PRI_ISP
set ip next-hop dynamic dhcp
set interface GigabitEthernet0/0
!
route-map NAT_ISP2 permit 10
match ip address NAT
match interface GigabitEthernet0/1
!
route-map NAT_ISP1 permit 10
match ip address NAT
match interface GigabitEthernet0/0
!
!
snmp-server community public RO
!
control-plane
!
!
!
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
transport input none
!
scheduler allocate 20000 1000
ntp server 129.6.15.26
!
end
