Can 4000 W PSU be able to bear load on Catalyst 6513 Mixing PSU ? Cisco document shows that we can use a 4000W on this chassis. And a 8700W PSU would be limited to 6000W. That tells me, we might not need a 6000W on this chassis. Document also notes...
Forum Posts
I'm trying to configure this very old switch for dual VLAN ports Data/Voice an here is my config: no logging event link-status switchport access vlan 200 switchport trunk encapsulation dot1q switchport mode trunk switchport voice vlan 800 spanning...
Que tal amigos escribo en esta comunidad para ver si alguien me puede brindar información sobre un smart switch SG200-50, quisiera saber porque el led de system parpadea sin parar y esta en color verde pero no responden los 50 puertos tampoco me deja...
I set up VXLAN across 4 Nexus 9k - Most of the VXLAN traffic consists of video camera traffic. We notice that we can not access the cameras via HTTP and HTTPS across the VXLAN - We are able to get pass the loading page but video feed is not loading -...
i have two nexus 9504 connected via vPC link, and working as active passive as show in diagram. and i config the HSRP on both nexus, where NX1 has VLAN 30 with IP 10.20.30.2 (Acive)and the NX2 has the IP 10.20.30.3(Standby). and the Virtual IP is 10...
Hello,I have a big issue with routing over Nexus 7000 vpc peerlink....I am exactly in the case of the diagram 3 of the link bellow : http://bradhedlund.com/2010/12/16/routing-over-nexus-7000-vpc-peer-link-yes-and-no/My question is how can I resolve m...
Need to upgrade from Cisco 6506 to cisco 4510re switch with vss up.what are the steps before preparing configs
Resolved! Cisco Nexus 5600 LAG Groups
Hi guys, Could you help me with an information? I'm looking for how many link agreggation groups are supported at Cisco Nexus 5600 Switches Series. I found only the maximum number of interfaces per EtherChannel buy nothing about number of link agre...
Resolved! Dot1x - WS-C3650-48PD
I just swapped a 3650 out, put the original config on it and the dot1x config does not want to work and neither did the RADIUS. The switch I replaced it with must have a newer IOS on it, which needs newer commands. We have sorted the RADIUS with a di...
Resolved! Nexus 93180YC-EX with PBR
Hi, I have recently bought a couple of Nexus 93180YC-EX switches for a small datacenter deployment. These switches would also do the core routing for this datacenter. I plan to use VPC, SVIs, Layer 3 routing (EIGRP over the VPC peer-link) and also...
Resolved! C9300-48P-E Question
Are there any bundles or incentives when quoting several C9300-48P-E switches? For example a customer would like 10 of these switches. Thanks in advance.
So, I've been spinning my wheels on this for way too long now. I have a remote network that has a small office that's pretty far from their main network. All that's available is a very slow and unreliable T1 connection, and PtP radio connections. T...
Hi All !! Have two switch WS-C3850-24S and i want add to stack, but switch have different firmware. In one have WS-C3850-24S 03.06.02aE cat3k_caa-universalk9 INSTALL ipbasek9 Permanent ipbasek9 and on the other WS-C3850-24S...
Hi Experts, I'm New with Cisco Catalyst Switch, we were shifted from Avaya Stack Switches to Cisco Catalyst Stacks . My First question : Is Catalyst 2690-X do intervalan Configuration ?i have learned that there are some L3 Features Limitations !what ...
Hi, I am trying to copy running copy file in to SFTP server which i am going to configure cron job letter on for schedule backup. But i am unable to copy to SFTP. Can someone help me with this. Please find below error:- SW_01#copy running-confi...
