Power over Ethernet only?

[dal]

Hi.
Is i possible to configure a Cisco switchport to deliver PoE only? No data?

I need to power up a device that does not need data, but if I just plug it in, the switch log gets filled up with Poe Device connected / disconnected messages

Thanks

[guruvignesh · Accepted solution]

Hello Dal,

it's possible to configure a Cisco switchport to deliver PoE (Power over Ethernet) only without providing data. You can achieve this by configuring the switchport as an "access" port with the "power inline" command and disabling data transmission using the "switchport mode access" and "switchport access vlan" commands.

interface <interface-type> <interface-number>
switchport mode access
switchport access vlan <VLAN-number> # Assign a VLAN for the port
power inline static # Enables PoE without data

This configuration will deliver PoE to the connected device without allowing any data transmission on the port, reducing log entries related to data connectivity.

[dal]

Hi.

Thanks for answering.

But the solution didn't help

The log is still full of:

16:53:52.821: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/26: PD removed
16:53:53.793: %ILPOWER-5-DETECT: Interface Gi1/0/26: Power Device detected: IEEE PD
16:53:54.837: %ILPOWER-5-PD_ENTRY_REMOVAL: Interface GigabitEthernet1/0/26: power device entry removed, admin_state=STATIC oper_state=ON
16:53:54.839: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/26: PD removed
16:53:55.792: %ILPOWER-5-DETECT: Interface Gi1/0/26: Power Device detected: IEEE PD
16:53:56.831: %ILPOWER-5-PD_ENTRY_REMOVAL: Interface GigabitEthernet1/0/26: power device entry removed, admin_state=STATIC oper_state=ON
16:53:56.833: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/26: PD removed
16:53:57.801: %ILPOWER-5-DETECT: Interface Gi1/0/26: Power Device detected: IEEE PD
16:53:58.842: %ILPOWER-5-PD_ENTRY_REMOVAL: Interface GigabitEthernet1/0/26: power device entry removed, admin_state=STATIC oper_state=ON
16:53:58.843: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/26: PD removed
16:53:59.798: %ILPOWER-5-DETECT: Interface Gi1/0/26: Power Device detected: IEEE PD
16:54:00.840: %ILPOWER-5-PD_ENTRY_REMOVAL: Interface GigabitEthernet1/0/26: power device entry removed, admin_state=STATIC oper_state=ON
16:54:00.842: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/26: PD removed
16:54:01.794: %ILPOWER-5-DETECT: Interface Gi1/0/26: Power Device detected: IEEE PD
16:54:02.834: %ILPOWER-5-PD_ENTRY_REMOVAL: Interface GigabitEthernet1/0/26: power device entry removed, admin_state=STATIC oper_state=ON
16:54:02.836: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/26: PD removed
16:54:03.817: %ILPOWER-5-DETECT: Interface Gi1/0/26: Power Device detected: IEEE PD
16:54:04.831: %ILPOWER-5-PD_ENTRY_REMOVAL: Interface GigabitEthernet1/0/26: power device entry removed, admin_state=STATIC oper_state=ON
16:54:04.833: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/26: PD removed
16:54:05.825: %ILPOWER-5-DETECT: Interface Gi1/0/26: Power Device detected: IEEE PD
16:54:06.813: %ILPOWER-5-PD_ENTRY_REMOVAL: Interface GigabitEthernet1/0/26: power device entry removed, admin_state=STATIC oper_state=ON
16:54:06.815: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/26: PD removed
16:54:07.804: %ILPOWER-5-DETECT: Interface Gi1/0/26: Power Device detected: IEEE PD
16:54:08.843: %ILPOWER-5-PD_ENTRY_REMOVAL: Interface GigabitEthernet1/0/26: power device entry removed, admin_state=STATIC oper_state=ON
16:54:08.845: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/26: PD removed
16:54:10.801: %ILPOWER-5-DETECT: Interface Gi1/0/26: Power Device detected: IEEE PD

---

This is the port config:

---

switchport access vlan 1098
switchport mode access
power inline static

[Leo Laohoo]

What is this PD and how much power is it meant to draw?
Post the complete output to the command "sh interface Gi1/0/26".

[dal]

Never mind, the solution from @guruvignesh works as intended as soon as I connected something that actually draws power.
No more excessive logging; just three entries, and that was when I plugged the device in:

%ILPOWER-5-DETECT: Interface Gi1/0/26: Power Device detected: IEEE PD
%LINK-3-UPDOWN: Interface GigabitEthernet1/0/26, changed state to down
%ILPOWER-5-POWER_GRANTED: Interface Gi1/0/26: Power granted

Excellent!

This is the switchport config:

interface GigabitEthernet1/0/26
 switchport access vlan 1098
 switchport mode access
 power inline static
end

As for the device I wanted powered, it is a PoE to Micro USB adapter 
But in my case, I just need the power to power up a HAN meter in my fuse box

Thanks!