Hi Experts,I have the following scenario. There are two pairs of firewalls in active/standby HA. One pair is used to filter east-west traffic and the other pair is used for north-south traffic.E-W traffic:Currently, a E-W PBR contract is applied on v...
Forum Posts
Devnet APIC always-on sandbox has not been available for 1 week? Will it be up again and when?
Hi , I have a case where I need to leak between an EPG connected to a VRF-internet that provides internet access through F5 , while VPN access is provided through another VRF-VPN I need to Leak the EPG sub-net from vrf-internet to vrf-VPN L3out EPG ,...
Hi team, I can’t register APIC with CSSM on-prem. I used a command on APIC CLI: apic(config)# license smart transport-mode on-prem url <URL was collected from the software itself> I monitored and the license is still not updated. Connection from APIC...
In what scenario does 'api/node/class/epmIpEp' API return 'unspecified' for ifid?My understanding is that 'ifid' is the name of the interface on the leaf interface to which End point in question is connected.Please help me understand if this value ca...
Hello,I hope I can get some help. We have a project to deploy IPv6 on all environments in our data center. I am working on the ACI.I created a separate interface profile off of the existing Node Profile for IPv4 to accommodate IPv6 L3out.This is inte...
Hi there, I am coming from an N5K - N7K setup, where I know that N5k regularly do cut through switching and N7K always store and forward.That is relevant to know in regards to how broken frames (CRC errors) are discarded or spread through the fabric....
has anyone tried before automating cisco ACI using excel sheets , by filling ACI Objects and uploading them to ACI ? If yes , do you have any template to be followed?
Resolved! Cisco ACI Multisite - ISN
Hi, Basically this is simple question. But, I'm still confused even I have read document cisco ACI multisite whitepaper. Basically, ACI use MP BGP EVPN (between spines) to build underlay between sites. Hence, it is needed to configure OSPF and BGP b...
Resolved! moquery filter
Hey Folks,Maybe you can help me out: i am using a visore filter to find an ip/subnet and where it is used/routed. https://xxxx/visore.html#/&class=l3extSubnet&propFilter=query-target-filter=and(wcard(l3extSubnet.ip,"10.49.254.0"))Now i am trying to g...
HiI am working on an ACI Fabric project and fairly very new to the technology.Most of the service provisioning for the platform is automated. Currently, EPGs are statically binded to the ports ports from the Leaf switches. I tried to find out how you...
Hi,I would like to decommission/remove a LEAF from an ACI Fabric to use it for another Fabric.I followed this procedure https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/4-x/troubleshooting/Cisco-APIC-Troubleshooting-Guide-42x/Cis...
Hey All, Would like to seek your inputs regarding ACI VM Simulator. From the link below, it says "The simulator allows you to connect external management entities such as ESX servers, vCenters, vShields, bare metal servers, L4-L7 services, AAA sy...
Resolved! ACI Brownfield to multi-site
Good day,I have an existing production fabric and I'm spinning up a Greenfield DR fabric. I am worried about potential service impact(s) to my production fabric when adding it to multi-site. The "tl;dr" of my post is: Is there a service impact when...
I'm getting the below fault error in SPINE switch. Node-202/sys/phys-[eth1/3] port is connected to LEAF switch pod-1/node-101/sys/phys-[eth1/49]. Please suggest me how can I solved this fault error.Fault Code: F100696Affected Obj:topology/pod-1/node-...
