Data Center Switches

Happy 4th everyonePlease help me out to understand the no connectivity issue i am experiencing for one of the VMs "V1"please see attached text config fileinterface Vethernet7  inherit port-profile data_vlan172  description V1, Network Adapter 1  vmwa...

Hi all,Can the port profile in nexus1kv be assigned to the specified uplink? For example, if I have two uplinks and one vm connect to the nexus1kv, and I want the traffic from this vm only go through one of the two uplinks, how can I configure that? ...

Hi all,I got a problem when I install nexus1kv on my esx host. The vsm is successfully connected to the vc, and the status is:acl-nexus(config)# show svs connectionsconnection vc:    ip address: 10.117.8.38    remote port: 80    protocol: vmware-vim ...

Dear all:    Do I need to reinstall VEM module or reconfig it, after replace ESX host NIC???FYIJames Huang

Hi,since december we have the nexus 1000v in our company. Everything working fine and looks good. We have a ESX cluster with two hosts and 7 NICs uplink. Today after a long time i have a look in the logging and saw this:Dropping received frames from ...

Hi,I have a data-centre with three clusters configured.  I have installed a Nexus 1000V with Primary / Secondary VSMs in one cluster and all is working well.I have now installed a new 1000v and VSM on the second cluster and have successfully created ...

Hi We are evaluating the NEXUS 1k as we would like to use LACP on the uplinks to our  VM-ware hosts. I'm able to configure LACP to the VEM that is on the same host as the VSM. Enabling it on another host with only VEM will bring the interfaces  to...

Is it possible to port channel 2 10G ports on the Nexus 1000V (Emulex CNAs) with 2 10G ports on the Nexus 5000 if the ports on the Nexus 5000 ports are also doing FCOE?I am getting the following error:N5k(config-if-range)# int  e1/5-6N5k(config-if-ra...

Hi,I'm running into an issue when installing Nexus 1000v VSM on an evaluation copy of the Vcenter Server 4.0 - it does NOT allow me to pick up the server. I'm doing OVF template installation through the vcenter GUI.Does the evaluation version of vCen...

Hi All,I am very new to Nexus1000v. I am trying to install it on Blade server. I have three servers, one with vCenter in vlan 100, other two with ESXi 4.0 have two pNICs. i have installed the VSM in one esx server whose service console in vlan 100 ha...

Hello,Anybody else seen the issue where it takes like 15 seconds to sh a running-config on the 1000v. Fairly annoying for sure. I've seen this in the past and resolved it somehow but not sure. After having an issue and having to rebuild my 1000v it's...

Hi all,I know that we can run script with run-script command in nexus1kv. But how can I write the repeated command in the script? Does nexus1kv support the loop in the script, such as for or while? I can't find the material about it. Thanks in advanc...

Hi all,I tried to install the release 1.2 Nexus 1000V with the new automatic installer. Deployment runs fine, but in the installer, after choosing the VSM VM and assign the VLANs I got the message "the choosen VM does not appear to be a Nexus 1000V V...

Buenos días.Estoy por realizar la compra del Nexus 1000V pero tengo duda entre dos números de parte casi iguales pero con la diferencia de:1.- Nexus 1000V eDelivery CPU License Qty 16 (1YR Min Service)2.- Nexus 1000V Paper CPU License Qty 16 (1YR Min...

There are several commands listed in the troubleshooting guide for VEM health status on ESX hosts from the command line. I'm not having any luck finding any commands that might work over the VMA connecting to ESXi hosts. Does anyone know of any comma...