Good morning all, i am new to the whole Cisco forum. I have a major issue, i work as a contractor for the US Coast guard as a system Admin. I was told by the cisco tech to try to find a resolution here on the form. The issue that i am experiencing is...
Forum Posts
Resolved! vPC and Gateway
hello guysi setup a vPC scenario as shown in the picture. server 1.1.1.100 can ping 1.1.1.120 and 130 and vice versa. the link failover or switch failed will work fine.but server in vPC switch ( here is server 1.1.1.100) can not ping 1.1.1.1 (3164-A)...
HelloPlease see attached, the x2 Nexus 5k Switches are configured has a VPC pair already VPC domain 10I want to configure ibgp between the Nexus Switches and the IOS Sack, the IOS Stack is runing EBGP peering with ISP Router,we have subnets Southbou...
We are migrating from a pair of core Nexus 3548 to to a pair of 3548-xl. I am asking what's the best scenario to do this? Any one has similar experience?
Hi guys, I'm going to configure VXLAN on nexus N9K-C93108TC-EX but L2VNI no connectivity. Network topology diagram:https://prnt.sc/2346bcn At the all I used VLAN with EVPNtwo leaf switch can learn Mac addresses from each other through EVPN but L2VNI...
compliments of the season Cisco community.I want to grant permission to any client outside, to access a tcp service on server within my LAN with IP 10.30.0.3I entered the instructions below but still can't access the service from outside. please can ...
How do I increase the number of mcast groups for feature vxlan. It looks like I can only get 128 out of it. This is the error the C9372PX is giving me. VDC-1 %$ %ICAM-2-SCALE_THRESHOLD_EXCEEDED_CRIT: Utilization of 114 percent for feature BGP Mcast g...
I need to perform a Port mirroring from a source in one Aruba HPE Switch, crossing other Aruba HPE switch and then ending in two Nexus switches.I know there is the option of RSPAN to perform Port mirroring between different devices in Cisco switches....
HiWe have a pair of Nexus 5k in VPC domain and these connect to a x2 stack switch through a vPC, the stack switch is already runnig BGP where we peer with ISPif I were to configure BGP Between nexus 1 & 2 and Stack Switch would I use ibgp or ebgp ??...
Hi Cisco Community,I am trying to enable openflow in nx-os 10.1 in 9300v... but i can't find the option "feature openflow". Does someone know how to enable that?
We need to know if the 9706 Multilayer Director Switch complies with the protocol SLAP: Switch Link Authentication Protocol
Resolved! Switch Link Authentication Protocol
Hello Experts,We need to know if the IBM Storage Networking 9706 Multilayer Director Switch complies with the protocol SLAP: Switch Link Authentication Protocol
Resolved! Adding a VLAN to a VPC
Hi! I am striving to add vlan10 to this VPC trunk. Here is what I have :int Po1swichport mode trunkswitchport trunk allowed vlan 8,9,10speed 10000vpc 10 On both switches. I just added Vlan 10 and it does not work. Any clue ?(or is it the BigIP right...
Hello,I want to setup L3 routed port-channel from Router to 9Ks that are vPC with each other and then run OSPF over them, so how can I do that? as far as two 9Ks has their own control plane, see below image.
Hi i am doing a battery count on site for EPCRA reporting and we have Cisco Catalyst 4500 on site. I am wondering if it has any battery in it?
