Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, how can we setup a users unity voicemail to play a greeting but keep the inbox closed, preventing a caller from leaving a voice message? We would like to leave an informational greeting but not allow the caller to leave a message.
Hi AllI have had issues with a SIP trunk to one of our older telephone systems, The SIP trunk on the Alcatel system can only be built to 1 ip address on the call manager, what I have found is phones which are in the same CM group where the trunk is b...
Hi.. I had to change ip adress of CUE but after changing ip i am not able to login on CUE through GUI with new ip address. The web page keep roll on but doent get to next page. Credentials are correct.Pls suggest what else changes i need to do.
My set up is an ISR 2901 with CME 10.5 with Viatalk Outgoing calls are working as expected. Incoming calls receive a busy signal. Further to this, there is no traffic to the interface. The voip ports are in fact opened to the world, so I know fir...
Hi,Having the issue with DTMF relay in according the following scheme: PSTN > Voice GW (MGCP) with ISDN PRI > CUCM 8.x > CUCX 9.1CUCX has IVR AutoAttendant with the ability (via 'Get Digit String' and 'Call Redirect' steps) of extension/dn dialing.T...
I got cisco ATA 187 (for fax) and try to configure it on CME 9.0 but it not registred on CME.ATA platform : APP187.9-2-3-1 voice register global mode cme source-address 10.14.20.254 port 2000 max-dn 80 max-pool 80 tftp-path flash: file text!voice reg...
Dear All, currently i try to register ata 187 on CME.when i debug tftp event, i keep searching for the firmware:*Jan 17 09:05:00.583: TFTP: Looking for CTLSEPE16D1508A901.tlv*Jan 17 09:05:00.807: TFTP: Looking for ATAE16D1508A901.cnf.xml*Jan 17 09:05...
Hi,CUCM 10.5, MGCP VGW with E1sRequired to make a group of users to make external calls with the same external number. i.e. the shown Calling number at the second end will be the same, whomever the user made the call of this group. Regards.
Dears, I have an issue with VIC2-2FXS Card that have one port working fine and one suddenly Failed I replaced the card (Installed in cisco 2801 router) with another new card VIC2-2FXS and it work for 30 minutes then the same port failed again the oth...
We are a small business with a Cisco IP phone 7931. Although we can call out on our line, no one can get through to us. The phone continues to ring and does not flip over to voice mail. Has anyone else had this issue and, if so, how did you rectify i...
I have a analog cordless phone programmed. The DN for this phone also appears on six other phones. This way they can answer the call from their desk or cordless phone. When they answer the call from the digital desk phone it puts the cordless phone i...
Hi all, I want to block some calls for some ANI numbers. Our CUBE has several SIP connections to different devices Calls come from Telco SPCUBE to our cube and then it goes to either CVP or CUCM Here are dial peers and translation rules I creat...
Hello Everyone,I have two CME sites connected via P2P. I have configured dial peer for calling between two sites. Calls from one site are working but from other site I am not able to make calls. Anyone can help me with this issue?I am attaching debug...
HI allI have cucm 9.1 which is working properly. how can i make someone call and connect to conference call from his/her mobile phone.please helpthanks
One of the user is facing issue with cisco 7942 hard phone. Missed call logs is empty in the directory.CUCM version:-8.X On verifying the line setting missed call log parameter check box selected. Any input on this would be helpful.
