Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, I need your kind help in assisting in the below given scenario.I have one extension on which Busy trigger is set to 2. Now the case is like that when my extension is on call, i can get maximum of 1 call and i can see the call waiting on my scrree...
hiwe are using one 2960 switch and one 2911 router and one server for call manger(esxi server ip 192.168.1.1)call manger ip 192.168.1.10router ip 10.26.27.254switch vlan 1 ip 172.26.27.100voice vlan 10 10.26.27.254data vlan 172.26.27.254this call ma...
Looking at the supported hardware for CME 4.0, the 6941 is not listed.http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/cme42spc.htmDoes this mean it is impossible to get the phone working with CME 4.0? Or could I download firmwa...
I'm trying to figure out how to setup DIDs on the CMBE 3000, I have read the admin guide and watched a few setup videos from Cisco on YouTube but haven't found anything on how to setup DIDs.The goal would be to have each phone assigned a DID as the e...
Hello,I have one gateway 2911 (E1/8 FXO/4 FXS) managed by cucm (8.5) using mgcp. E1 is working fine,FXS workingbut FXO hanging up every incoming call. I got some strange errror from debug mgcp errors: Feb 12 13:10:12.125: //-1/xxxxxxxxxxxx/MGCP/mgcp...
Hi All,I hope someone can help me out. A while ago I came across a document on the Cisco website that showed me how to transfer incoming calls to multiple lines on the same phone. I can't for the life of me find this one again.The scenario is I hav...
I have a strange setup running a PLAR line off of one of my FXS lines in my 2921 router.With all FXS portws setup for MLPP, I can pickup the handset acess the MLPP code and dial with no issue., ie dial extension 1234 with MLPP code 80 - reulst is dia...
We are running CUCM 8.6 with 8945 handsets.In the Personal Address Book, we would like to create approximately 50 entries on each handset.Is there a way to set these all up on one handset and then copy them to all the others?
I do not know much about the setup yet but I was just hoping for some ideas on what to look at, or possible causes. I have a few sites that the call completes but no one can hear any sounds for site to different site only. Internal to the same site w...
We are taking wireshark traces behind Cisco phone using phone options.After making some calls, in wireshark - under Telephony --VOIP Calls option, it does not show any calls.But we can see RTP flow between Phone and SBC in normal packetsWhat is the b...
I have a user that is not able to listen to a message: They go into the vm and cannot retrieve the message, message unretrievable is what they are being told and message is dated 2/1/2013.I'm new to unity, is there a way I can retrieve the mess...
Hi All, We bought an expansion module 7916 for our receptionist. We are running an UC560. How do we configure the UC560 to support this new 7916 model? And where can we download the firmware/files for the 7916?Thanks,Tom
Hi All, We added a couple of new users via the CUE web admin page and their phones and extensions are working fine. The problem we have is we can't find them in the dial by name directory. Please help!Thanks,Tom
Hello ,I have this MCS7825I4-K9-CMC2A Server with Software 7.1.2-U-K9-7825We need to check if we could upgrade it to v9.0 without Hardware replacement.Thanks in advance,
Is there a way to disable auxiliary port on the back of a Cisco 7945G phone via call manager. Thanks
