Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I need some help getting my 4 port FXO module working on my 2901 router. I realize that I need to use the voice-port command to activate and configure the module but I don't know what port(s) the 4 port FXO modules is using. I performed a sh interfac...
Hello,Can I use Single Number Reach to achieve the following scenario:The incoming call will hit a Hunt Number --> Group of Extensions --> in case no answer the call will be forwarded to Mobile Number (I will use here SNR to keep the signalling withi...
Hi all, Can you please advise on best way to get all required info to complete the SME sizing tool? The SME sizing tool requires the following input parameters: BHCA per user for each trunk interface to leaf clusters for intercluster callsBHCA per us...
Hello, at the moment we´re restructuring our network. Currently we´re using more than 300 Cisco Vo-IP-Telephones in two /24 subnets. To make our network easier, we would like to transfer the two /24 subnets into a /23 subnet.We´re using the Cisco Uni...
I have a raised a request to the respective team to VMotion the existing VM running CUCM 10.5(2) version from existing host to a new host. So I would like to know about the things regarding CUCM which I should note down or take care before and after ...
I have setup CUCM and unity to have voicemail, I can ring an extension and leave a message, the message light then comes on on that phone but when I dial the voicemail I enter the pin and then each time it asks me to setup a greeting? I cannot get...
I am going to be using CUCM with my 1841 router as it's slient and compact, I am wondering how I setup the router to work with cucm Config: 1841 - 10.11.75.1 PoE switch - 10.11.75.2 Cucm - 10.11.75.3 The phones will be connected to the poe sw...
i want to add a secondary ip address on the H.323 gateway interface so that when this vlan goes down the secondary ip is up but im wondering will it affect the gateway operations? do i need to add another "h323-gateway voip bind srcaddr <secondary i...
Hello Team, Enclose is the configuration, kindly open in Wordpad. During SRST mode, Hardware conferencing is not working with SIP 7841 or 3905 IP Phones.. whereas conferencing is working perfectly with 7841 phone because it is working internal br...
Hi Every one I have got 2900 router and trying to enable E1 port. Not able to configure the same. by going through the document found UCK9 type should be in EvalRightToUse but on my router it is RightToUse. is this cause of the issue.
Firstly - I am a newbie in this field so please answer as such. Thanks. I am running CME 7.1 on a Cisco 2900 series router using SCCP. I have been adding phones (7941's) to the system and all of the new phones are not able to access touch tone servic...
Dear I have Unity connection version 9 Windown 7 64 bitFireFoz 20.0Java 6 update 34 and i tried jave 7 but the same problemwhen i go to sustem handlers >greeting > arabic or english > i can play or record or upload the WAV file , but when i go to h...
Hi Folks, I tried to connect vg224 with cme 2851 by sccp, and once i finished the configuration as shown below, i listen fast busy tone once i off hook the analoge phone, and make sh ephone on CME: CME#sh ephone ephone-2[1] Mac:2C3F.38C9.1007 T...
Hello Friends, I am trying to configure ESRST.. with Class of restriction. the phone whose mac address is added into SRST router with appropriate COS.. are only registering in ESRST mode when authentication register command is their is voice regist...
Hello,Is it possible to install two different clusters (2 publishers) in a Cisco UCM BE 6000 Edition on the same UCS hardware?Regards
