Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
hello all, I have a cme , registred with ip phones SIP, the problem is when i would make a call outside by FXO, I wait 12 to 15 seconds for the call to startI wait 12 to 15 seconds for the call to start can you find in attachement the global conf...
Hello, When a Cisco CP-6941 IP Phone user, search a contact from another country which has a phone number that ends with number “8”, from the IP phone’s company directory and dial it by pressing the centre button, string of 8 is being added automatic...
Hi All, Could you please let me know you ideas how you would configure a Cisco VGW with multiple PRI interfaces to be able to handle more service providers? Currently they are configured with MGCP, where it is simpler, as CUCM can control the inter...
Hi All, How to I remove the unwanted numbers on the monitor-ring type. Sample: voice user-profile 11 pin 1212 user 707 password 1212 number 707 type normal number 716,715,718,719 type monitor-ring How do I remove 716 and 719 in command form? Regar...
Hi all, I try to enable Deskphone Video together with a 8841 phone. - In Jabber: Status: Not available Reason: Unknown - PC is behind 8841 - Windows firewall is diabled for testing - Jabber Desk Phone Video is installed (4.1.6.0127) - JFW 11.7.1 - 88...
Would like to know the phone models supported for cucm version 11 and where to get the document to be found ? Thank you
I have my Cisco 8821 registered and obtained configuration (Directory Number, Line Name and etc). from CUCM. Everything looks good, I can receive incoming call and make outgoing calls. But the status is not reflecting in the CUCM, status still showin...
I am testing one of our remote sites ability to dial 911 when the WAN link is down. My question is how long will it take for the phones at this location to re-register with the router to make an 911 call? The phones at this site normally register wit...
Hello, I used to have caller id blocking on CUCM 9.1 if you press *57 before dialing number, so user can call without showing his phone number. For some reason it stopped working and if I am dialing *57, I can here busy tone right away. I have a ro...
Hello Cisco Community, I wanted to get your advice with the configurations of a third-party SIP phone device in a CME environment. The problem I am encountering is that after configuring the "voice register pool" and "ephone-dn" for the SIP phone we ...
Hello Guys, the clock is set right on CME. we are in Angola, time zone is UTC+1 west, central africa. i understand that this time zone is not supported by my CME so I tried to set it to greenwich time but still 1h.16 min late though it should be the...
We currently have a single CUCM and UCCX (HA) cluster. We purchased through cisco a NFR to add an additional CUCM and UCCX cluster strictly for in house testing. We integrated the 2 via a SIP trunk and would like to know the best way of routing cal...
We have the ACD line in our pharmacy. Our IT dept doesn't know what options are available for altering the current setup. Can it be set up so the pharm techs aren't automatically logged out after 3 rings if they don't answer? Can it be set up so that...
Hi, I am searching for a good 3rd party reporting software that can integrate with call manager 11.x platform and provide real time customized reports on phone inventory, associated extensions, voicemail, etc. I came across uplinx and unimax reportin...
Hello @ all, Is there any way to statically specify the media ports used by the RTP stream? I have the following issue: A soft phone is registered to CUBE via SIP. On the CUBE router Zone Based Firewall is configured to also allow only defined traffi...
