Good Afternoon My company has set up a new office, I will call "Central". We configured a 3850 switch connected to a ASA 4406 firewall. Every is working fine except for one problem. I can't connect to printers, servers, or computers in our other ...
Good Afternoon My company has set up a new office, I will call "Central". We configured a 3850 switch connected to a ASA 4406 firewall. Every is working fine except for one problem. I can't connect to printers, servers, or computers in our other ...
Hi Can some one please advise. I have a router running ISDN BRI connection, dial on demand (model 2811) ISDN BRI has 2 channels, I am wanting to execute the command dialer load-threshold xxx either to use the second B channel if the first B channel r...
Hello, We just put in fiber at one of our rural locations. I am hoping to do this configuration remotely with a reload in x as a backup. The site is currently on an MPLS using BGP. I need to move it over to our fiber cloud, which uses EIGRP. I...
We have a 150MB TLS type circuit between our 2 main sites, connected to GB fiber ports on each end via Cat6509. File copies between servers with GB LAN connections 1 direction are fast (3 seconds for a 20MB file) but can take as long as 90 seconds th...
Hi there Guys I have a cisco 2621 router. It has worked before, although now it is coming up with the following message during boot up: System Bootstrap, version 12.2 (8r), Release Software (fc1) Copyright (c) 2003 by Cisco Systems, Inc Then I g...
We have two sites that are connected to MPLS. The service provider has a PE router on site at each location. They are running BGP for our WAN which is extensive. It is private EBGP so each site has it's own ASN. We are redistributing OSPF into BG...
Hello All,We have a requirement to limit traffic to 1 Mbps on WAN links based on a specific source & destination ip address pair. The purpose is to limit the rate to 1 Mbps for a copy operation between a server and client over the WAN. Microsoft Robo...
I am running GSN3 on my laptop to create a test invironment, and after write erase, how long shoudl ir take to reload? Mine has been runnng for aobut an hour now.
Hi, We are in the process of deploying nbar 2 throughout our organisation for better application visability. A lot of our internal applications are SSL and accessed via a browser, however. These applications have a wildcard certificate e.g. *.organ...
Hello, Just wondering if someone has experience upgrading to 5506H-X. I need to preserve the network, credentials and rule configuration from the1811. My plan is to transfer the configuration file via TFTP to the 5506. Is there any existing upgrade d...
Hi Team, Silly Question! I am wondering where to look to add modules to my cisco router 1841 and 2851 I only need to add Ethernet interfaces but I don't know how to look for them. :/ I know there are quite a few with Codes but thats where I get confu...
Hi All in Router i am the getting error:AMDP2_FE-6-EXCESSCOLL: Ethernet0/0 TDR=1, TRC=0Router is connected to Switch, both router and switch config is belowcan some body tell me how to fix up this issue as i am planning to change Duplex setting route...
I'm running eBGP with two ISPs on a single Cisco 4331. ISP A is a 100Mb connection, ISP B is a 20Mb connection. If I perform a "show ip route" about 60% of my outbound routes route thru ISP B - the smaller connection. How can I force more of my outbo...
Hi there!!! :) Basically I am wondering if I can do GLBP with Track between 2 interfaces on the same Router. Both interfaces are L3 on same Subnet. 1.1 and 1.2 So Can I use GLBP between thoese two and create a Virtual IP which will be Load Balance ...
Hello everyone, I have router configured in NAT, with 3 vlan's for certain purposes and DHCP server for each one.I show the configuration of the router, however and with regard to IPTV in Vlan 20, the STB only works for a few seconds and the image fr...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-03-2024 01:45 PM | ||
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-26-2024 05:26 AM | ||
04-24-2024 03:30 PM |
User | Count |
---|---|
14 | |
6 | |
4 | |
2 | |
2 |