Hi,While the telecom team ordered a new circuit, I saw access speed and port speed on the quote.Would you please tell me the difference between access speed (5M) and port speed (1M) and what how they work? Please see the attached.Thank you in advanc...
Forum Posts
Dear Experts, We have a setup configured with Two different links connectiong on two different routers.Below is the BGP configuration. Router-1 Configuration : router bgp 200 no synchronization bgp log-neighbor-changes network 10.20.20.0 mask 255.25...
Resolved! How does CPU affect performance
Hi AllCan anyone answer me a question around CPU on routersIf I have a 2811 for example running a number of ipsec tunnels with qos on them, and the router is running at 98% cpu.what is the effect on this on traffic going through the router? will it d...
Resolved! Cisco 2811 on Centurylink
So I'm just starting out with Cisco and my boss gave me a 2811 to practice on. I figured I would replace my Centurylink router with it. I was able to find information online and put together the config listed below. I can ping out to Google, my WA...
Resolved! ASR 1001-X Default Queue Congestion
Hi,We are running a MPLS based DMVPN to about 60 sites. We have a mix of bandwidths and are using per tunnel QOS in order to match each sites bandwidth. Our 4Mbps sites are experiencing issues where traffic destined for the default queue takes up mos...
Hi Community,I have a question, I have been experienced packets lost in LAN, my question is when I ping the dest with 100 repetitions for example I dont get any packet lost but if I ping the destination with 500 repetitions always I get some packets ...
Hi, I'm trying to change the cellular PRL Region on a C897VAG-LTE-GA-K9 to 3. But it's showing "Failed to change PRL region". Router#cellular 0 lte prl-region 3!!!WARNING: PRL region view/set requires modem reset, call will be disconnected!!!Are you ...
Playing around with some old equipment at home, I have this setup but am unable to browse the net. Pretty basic setup but i'm unsure how I have misconfigured?Both the 7301 router and laptop can ping out but thats the extent of the connectivity Cable ...
Hi Team,We are deploying a IPT in our office with variant IP phones models that are 3905/7821 and 7861.In our network we are using cisco SG500 has a core switch and DHCP server also and we have cisco SG300 as a access L2 switch on which our laptop/de...
We are using a Cisco Catalyst 3925 running IOS 15.1 (R1) with an integral ES2-48 switch (S1) module in a lab environment. The modemis provided by Comcast. Consoling into R1 I can resolve domain names and ping them with no issues. However, while the S...
I perform a wr erase to the Cisco 3900 but after the reload the router is not responding. i only got this message from the console and i really dont know what to do: € D@fÆÎÌÌŒŒŒœÿÿ€B D@fÆÎÌÌŒŒŒœÿÿÿD€fÆÎÌŒŒŒŒœÜ¿ÿÿ€B D@˜ÆÆÎÌŒŒŒŒÜÿÿ
Resolved! OSPF Redistribution Commands
What, if any, difference is there between these commands? This is how I see it configured:router# show run | sec ospfredistribute static metric 10 metric-type 1 subnets route-map static-to-ospforWould this be the same and/or overlapping:router# show ...
Hi all,We are having problems to configure a L3VPN in VIRL with an MPLS CORE NETWORK that uses RSVP-TE as label exchange protocol and IS-IS as IGP protocol. The idea is to distinguish different type of traffic from the CEs to route them on specific M...
TopologyCE1---PE1----PE2---CE12I have gone through different online resources so far but did not get the answer why we cannot create L3VPN without using LDP/RSVP.As per RFC 3107 BGP canbe used to distributes label without any requiremnt or label dist...
Jsut curious if anybody has seen this. I have 4 Metro Ethernet switches. I have access to these switches from a network monitor for backups . However one switch is not working. I can ping it from the local switch it is directly connected to, but not ...
| User | Count |
|---|---|
| 14 | |
| 6 | |
| 3 | |
| 2 | |
| 2 |
