About KMNRuser

KMNRuser · 02-27-2024

We are trying to get a configuration off of an older, no longer in production 3850 (C3850-48T).I am following instructions which is to say that i have:1. Depressed and held the mode button down while plugging the switch into AC power.2. Wait and wa...

KMNRuser · 12-14-2023

We have one of our remote sites connecting back to us using a Cisco C8200L-1N-4T. This router is in a remote location, and the only service we could find out there was cellular.We have the Cellular interface connected; using "ip address negotiated".W...

KMNRuser · 12-07-2023

I am using the Embedded Packet Capture feature on a C8200L-1N-4T router.I have the capture and need to export it to our TFTP server.When i run the following command:8200_RTR#mon cap DMVPN export tftp://192.168.1.146/Community.pcapI get the following ...

KMNRuser · 12-04-2023

We are implementing a new DMVPN network on our production routers. It is in addition to 2 existing DMVPN's that we use.We have a hub at Headquarters, and another Hub at our DR site.We have a tertiary DR site where we are trying to implement.When i i...

KMNRuser · 11-15-2023

This evening i am moving our 4431 ISR from 16.6.4 Everest to 17.09.04a Cupertino.I have pulled down the file entitled "isr4400-universalk9.17.09.04a.SPA.bin" and have it loaded on a usb stick which i can read on the router at usb0:.I have used the "i...

KMNRuser · 02-28-2024

We were able to use this document https://www.rogerperkin.co.uk/cisco/password-recovery/password-recovery-cisco-catalyst-3850/ and do a password reset. The only procedure that worked was:1. Plug in the 3850 WITHOUT holding the Mode button.. you hav...

KMNRuser · 02-27-2024

Balaji,Thank you for your response. I have attached the log output. it is almost as if the Mode button is inoperative. I feel it depress, but there is no indication in the output that the MODE button is ever pressed..

KMNRuser · 01-11-2024

Rick,Yes you are correct..Tunnel 6 is the ipsec-isakmp tunnel I am trying to bring up.Here is the config of the tunnel at the HUB. This box is an 8200 router.interface Tunnel6ip address 10.101.6.1 255.255.255.0tunnel source GigabitEthernet0/0/0tunne...

KMNRuser · 01-10-2024

Rick,I did go back and add an ACE for the ACL entitled GREINIPSEC. it now looks like this on both sides:ip access-list extended GREINIPSEC10 permit gre any any20 permit udp any any eq isakmpUnfortunately this did not resolve the issue; once again th...

KMNRuser · 01-09-2024

Rick,I wanted to get back to you and let you know that i did change the tunnel mode from transport to tunnel on both sides. Unfortunately that did not resolve the issue. One thing i am struggling with is the persistent logging. I would think that ...

Member Since	‎05-14-2020 06:48 AM
Date Last Visited	‎04-24-2024 12:05 AM
Posts	69
Total Helpful Votes Received	16

User Statistics

User Activity

3850 switch will not enter ROMMON mode

8200 router cellular interface shutting down

Embedded Packet Capture failing to export

No output on Hub router when issueing a "show ip nhrp" command

I would like to use "install" mode for upgrading 4431 if an option

Re: 3850 switch will not enter ROMMON mode

Re: 3850 switch will not enter ROMMON mode

Re: 8200 router cellular interface shutting down

Re: 8200 router cellular interface shutting down

Re: 8200 router cellular interface shutting down