Hi dearI want to order an access point with this part number: Air-Cap3702E-X-K9 , I just can find available Access point H register domain (H instead of X),now I wanna Know H is working in our domain or not?
Hi dearI want to order an access point with this part number: Air-Cap3702E-X-K9 , I just can find available Access point H register domain (H instead of X),now I wanna Know H is working in our domain or not?
Dear all, I am stuck by QoS behaviour when using my AP 3602 in local switching mode. Actually, I want to verify what is the DSCP to 802.11e UP conversion table in uplinks and downlinks.In uplinks (from the wireless client to the wired server), I have...
Cisco 5508 is new Wireless LAN Controller supporting new 802.11ac Giga bit Wireless. this has been plugged into LAN port of Small-Business Security Appliance SA 520 LAN port (trunk). Default vlan 1 works fine which is for management but data vlan doe...
Hi Team, How do I identify the active/standby units on a 5508 WLC cluster? Regards,Suthakar
Hi,I am using a cisco controller AIR-CT5508-K9 which supports the indoor 1242 access points. I want to purchase indoor access points as I understand that the 1242 series Access Points are coming to end off life. Kindly advise on which other model I...
Hi Guys, I have a Cisco WLC 2504 deployed in my architecture WLAN with 2700 APsNow I have software system version 7.6.130.0 and I'm thinking do the upgrade to 8.0.120. (ED)Someone Can give me some information about the differente between two versio...
good dayI have 3- 4400s controllers, running code 7.0.235.0, AP type 3502i, two controllers have 75AP each and the one with memory been high (%80) has 65APs.the first time I saw that, it was about %93, I believe average is about %65. so I rebooted th...
Hello,We have 5508 WLC controlling all of our APs in remote offices. Recently, users are complaining in one of our remote office for their connection is keep dropping. I'm very new to wifi network. I'm trying to find out where to start troubleshoot...
I can't find it anywhere, but how do I change the CLI password for a CMX running version 10.x code? I assume it's a cmxctl command, but I can only find one that I believe changes the GUI password.
Hi All, I need some help regarding mobility with 2504 and 5520 WLC's / MSE 8.0 and Prime 3.x 2x 5520 in Active/Standby , standby ip : 10.200.20.112 x 2504 in N+1 ip : 10.10.20.11 and 10.10.20.12I suspect that something is not right , im reading b...
Hi all,I have a Virtual WLC (software image version 8.1.102.0) with AP 1600 and a NPS service already installed with windows 2012 R2.I think, I have a problem with the MTU Size.The authentification doesn't match and if I look my Ethernet Frames, i ha...
in switch, I have one interface G1/0/35, type: trunk, connected to access point 2, in switch G1/0/35, can we list out the IP address of AP 2? how would I know the IP adress of AP under my switch under g1/0/35, currently, there are three mac address ...
Hi,I have a stack consisting of 2 WS-C3650-24PS (version 03.03 .05SE) configured as MC and 4 AIR-CAP3702I-E-K9.Everything is working properly and the APs are joined without problems, but only if the port of the 3650 is configured in access mode. This...
We got six 2960x switches (48-port) deployed this summer in our school and I have all our 3702i APs connected to them and they are powered by the PoE from the switches. But that will downgrade the APs to 3x3:3 mode. Our IT consultant told me that "yo...
Hi,I have purchased new Access point 3700 series (air-cap3702i-e-k9), please kindly guide me to configure. I have try to get global config mode but I can't get it. bestChandra
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-12-2024 05:27 AM | ||
04-10-2024 01:01 PM | ||
04-05-2024 06:44 PM | ||
04-04-2024 03:18 AM | ||
03-27-2024 07:38 AM |
User | Count |
---|---|
12 | |
8 | |
3 | |
2 | |
2 |