Hello,Can you connect a 1142N repeater to an existing 1142N repeater so as to lengthen the range?Do both repeaters have exactly the same config ?
Hello,Can you connect a 1142N repeater to an existing 1142N repeater so as to lengthen the range?Do both repeaters have exactly the same config ?
Hi,We have a Guest Wireless solution in place whereby we have 4 remote WLCs and an Anchor Controller providing the termination point for the Guest internet tunnels.We currently have an inconsistent issue, whereby idle clients are seemingly dropping t...
Hey All,just setup a few maps in WCS. 1 of our main building and the other 2 of the smaller buildings. The 2 smaller ones were simple and straight forward, however I'm getting some weird results with the main building.In the main building we have 1...
I have 4710 ACE load balancer with three virtual contexts, i have configured the three contexts with the syslog configuration to send the logs to a syslog server as below:logging enablelogging trap 5logging buffered 7logging host 10.x.x.x udp/514the ...
Hello guys,I would like to know how can i import Autocad files to WCS and see how the force of the signal can act in a especific area of my company.Thank you very much.
I decided to edit this since it got moved to a different place where it might not be understood:I have a UC320w phone system. I have SPA508g phones. I have a cisco POE switch next to the UC320. But, I have one far location that has one ethernet port ...
Hi all,Our organisation has multiple controllers at regional sites (one per region) & want to implement redundancy by placing one controller at headquarter's datacentre as a backup in case the site's failed.All our controllers are 5508 with 7.0.116.0...
Hello guysi have a wlc 5508 , and i want to enable LAG, but i want to connect 4 ports in one module and the rest 4 ports in another module, for example Gigabitethernet1/45 - 1/48Gigabitethernet3/10 - 3/13 both modules in the same core switch (6506) o...
What is the best/recommeded design to deploy guest access at the head office and branch offices? Each branch will have a local internet connection. The idea is to have internet traffic switched locally. The the wireless network will provides access...
I just enabled 5Ghz 802.11a/n on my Cisco 5508 controller.I see my client machine associted with 802.11a/n (it is my understanding that "a" is required for 5Ghz).Is there a way I can confirm I am in the 5Ghz range? (we have 2.4Ghz enabled as well)
I have seen the other posts about this Syslog entry but we are running 7.0.220 and thought it was supposed to be fixed in this version. Any thoughts? The scope isn't out of addresses.%DHCP-3-ADDR_NOTIN_POOL: pools.c:158 Error: Ip Address 0.0.0.0 is...
Hi,I'm been trying everything and searched the net for this without any luck this time. I found it a few years back, but now I can't.I want to make some graph with http://oss.oetiker.ch/mrtg/ that list how many clients that are connected.I know this ...
Can i claim a warranty for faulty wireless IP Phone Batteries instead of Wireless IP Phones through Cisco RMA. Also i have the valid Smartcare contract with Cisco.
Hi folks,Looking at putting wireless into a large open plan building (appxox. 80M x 40M) with two floors. We'll have up to 450 clients (combination of desktop and mobile devices) spread over both floors so need about 24 APs. With 12 evenly distribute...
Hi,I've an AP connecting to the backbone switch via 2 wireless bridge links as shown below. Currently, it is operating as flat lan.Would like to know if it can be coverted to vlan mode so that I can support wireless clients of different vlans at the ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-04-2024 02:21 PM | ||
04-12-2024 05:27 AM | ||
04-10-2024 01:01 PM | ||
04-05-2024 06:44 PM | ||
04-04-2024 03:18 AM |
User | Count |
---|---|
12 | |
7 | |
3 | |
2 | |
2 |