Rtr1 ----Cost1-----> Rtr2 (Area13)Rtr1 ----Cost1-----> Rtr3 (Area13)Rtr2 ----Cost10----> Rtr3 (Area0)Rtr2 ----Cost10----> Rtr4 (Area0) If i redistribute static route on Rtr2 then Rtr3 learns best route from Rtr1If i redistribute static route on Rtr4 ...
Hello,Very new to the world of ASA. I just purchased a 5516 model to use as my router for my home lab. The goal is to replace my ISP-provided router with the ASA. When I try to connect the ethernet cable from the ONT to my outside interface on the AS...
Hello, We have four ISP's routers was connected directly to SDWAN, and we will change the connection to be connect to SDWAN via Cisco switches, as the below diagram:Here is the configuration for two ISP's-ISP1 Router side:interface GigabitEthernet0/0...
Hi! I am sitting with a topology of:PC1 -- SW1 -- R1 -- SW2 -- PC2I am trying to configure a GRE tunnel between SW1 and SW2, but I cannot manage to make it work. Can someone help out? See below config. I have been fooling around a bit with the routes...
Good Day Cisco Community,I have a question regarding one of the steps while enabling cloud on ramp for SaaS (O365).When we select the application that we want to enable cloud on ramp for, we are directed to the currently active AAR policy (which is a...
Dears, i am getting the below errors any idea how to resolve it, the root cert is already installed.\ [28-Apr-2024 11:05:42 UTC] Install Certificate, on device caaaa438-ce6e-4afa-8b69-b896782de3f5, started by user "admin" from IP address "10.255.1.5...
Hello,Path of archive is configured as follows:path sftp://username:password@IPaddressofSFTP/The password is visible (clear text).Is there any way to encrypt password of SFTP in conf file?
Hello!I tested PPTP and L2TP VPN solutions, but considered another solution without the Cisco router involved.I've disabled all the virtual-access and vpdn stuff,sh run all | i vpdnreturns nothing, but the ports for PPTP and L2TP are still open and c...
Hello all,i have a problem.i have 4G router from ISP and the port is connected to HP switch then one of HP ports connected to my Cisco Switchwhen The power is off then on at 4G router .. the 4G router internet light became red and that's mean there i...
Hello,Need some help on the below code. we have 2 bgp path ( primary and backup) and i configure 1 subnet to be routed through main path and the rest 3 subnets through backup.on the backup i have the 3 subnet primary and the first subnet as backup ro...
Hello Community,Is there any command to turn-off the paging of the commands output on Cisco iOS and display all output without paging? On Dell Switches, there's a command "terminal length 0", but the same doesn't seem available on Cisco iOS.Router#te...
Hi, I have an intermittent problem where DNA Center seems to error out when provisioning templates to switches, the log says: Message: Unable to push the invalid CLI to the device 192.0.2.2 using protocol ssh2. Invalid CLI - 'terminal width 0'. C...
I understand that when implementing configuration changes from vManage to cEdge/vEdge, the changes are made via NETCONF.However, even if no allow-service netconf is set under Interface tunnel, the configuration can be changed without any problem.Why ...
Any way to reduce CSR1000v load on CPU in EVE-NG? It is very CPU Intensive and increases the temperature very much. I need to lab SR and I know of no other image for regular IOS or IOS-XE that supports that.
Would it make sense to use a firewall for a 10 gbps layer 2 link between 2 sites? I'm thinking using a firewall for a 10 gbps connection would be very expensive. Is it worth it?