Routing

I have created a new VTI. I see output drops incrementing. I migrated from a 100M circuit to now 1G. The old interface also had output drops which I attributed to an old 100M circuit. The new interface also has output drops. How do I troubleshoot thi...

I have a 2811 router with default route 0.0.0.0 0.0.0.0 192.168.1.1 (my ISP Lan-side interface).  I have DHCP server on the router for wired interfaces (e.g. 172.16.11.0 /24 through 172.16.18.0 /24) with 8 VLANs (711 - 718), but none of the 172.16 ra...

My next step doesn't seem to be working. I now have my internal clients all able to access the internet through one or two NATs. Here's my topology:Internet --- 2911 -+- mylocaldomain --- MEsh NAT router --- Local Server and clients ...

hi i attached file below. problem is that i connent to lans via router and config each and every thing again n again but the problem is data is sharing between lans but not to other lan network. urgent help will be appreciated. 

Hello All,  I can't believe, I'm not finding anything on the subject of running multiple EIGRP autonomous systems on the same set of routers. I'm hoping my Google skills are down. :) Here's what we are trying to accomplish and the problem we are runn...

Hi,We have mGRE DMVPN tunnle between one Hub and 7 Spokes. Other 6 Spokes are working fine but one Spoke is not connecting to Hub.Spoke shows DMVPN on IKE state (tunnle is not working) and Hub is not adding nhrp entry in table.Spoke DMVPN TunnelPleas...

Hello everyone,I have ASR 920 Router but when I switch it on it stuck after showing only these results  System Bootstrap, Version 15.6(43r)S, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com/techsupportCopyright (c) 2020 by cisco Systems...

Any way to reduce CSR1000v load on CPU in EVE-NG? It is very CPU Intensive and increases the temperature very much. I need to lab SR and I know of no other image for regular IOS or IOS-XE that supports that.

I need to enable directed broadcasts on some SVIs. Is there any difference between me using these two configs:acl 1 permit 10.10.10.1int vlan 1ip directed-broadcast 1ip forward-protocol udp 10ORacl 2000 permit 10.10.10.1 any udp 10int vlan 1ip direct...

Hi All,We have a URL which resolves to particular public ip and performance of that website is slow than expected from our office . We have a P2P link from office to DataCentre and from DataCentre it exits to internet. We observed the performance was...

I have following EEM applet: event manager applet FILTERCMD1 event cli pattern "^show version" sync yes action 001 cli command "enable" action 002 cli command "show users wide | include \*" action 003 puts nonewline $_cli_result Now if i run th...

Hi,I have upgraded my Cisco Nexus C93180YC-FX yesterday from NXOS 10.2(6)M to NXOS 10.3(4a)M, but I seem that I have an error when I make "sh logging last 10".2024 Apr 30 09:39:09 edge01.par03 %DAEMON-3-SYSTEM_MSG: error: Unable to open the btmp file...

PFA for your reference in SWinterface FastEthernet0/1switchport trunk allowed vlan 1,10,20switchport mode trunk!interface FastEthernet0/2switchport access vlan 10switchport mode trunk!interface FastEthernet0/3switchport access vlan 20switchport mode ...

Good afternoon:Run a simulation in packet tracer to implement a router on stick with two vlans. The simulation worked without problems, and I want to implement the same on my cisco 867VAE router.This equipment has a Giga interface for WAN (Ge1), and ...