Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
FMC MGMT PORT
by KayaaKashyap -
Azure ASAv - Have Dedicated Management Interface and use Outside
by mumbles202 -
Power Given, but Power Controller does not report power good C9200L
by Riimeister -
Does ise patch installation cause downtime?
by CCC3 -
Routing incoming traffic
by billseymour -
Cisco IR829 does not get ip address
by zentinelcorp -
If I disable ap status on c9800, will I not radiate the radio?
by CCC3 -
ISE- Profiling question
by babalao
Community Activity
vManage can not push the template to WAN Edge Device
Hi everyone, I have built the controller on-prem for lab. In the ver 20.3 everything is ok but when I upgrade vManage to 20.6, I can not push the template to WAN Edge Device, the error code is below: Server error: no registration found for callpoint ...
Adding new MDS switches into exisitng VSAN in NDFC
Hi there everyone, I'm reaching to see if anyone knows how to add new MDS switches into an exisiting VSAN in Nexus Dashboard Fabric Controller (NDFC version 12.2.1.316). This option was available in Data Centre Network Manager (DCNM) by going to Da...
Azure ASAv - Have Dedicated Management Interface and use Outside
So I've deployed an ASAv in Azure and it's been assigned a static ip for it's management interface. I'm able to reach the unit and configure it as normal, but I'm not able to remove the "no management-only" command from "interface management0/0". I...
ASA 5516-X Firepower Version Upgradation from 9.8(4)29 to 9.12.4.67
Hi,Can anyone please provide me the procedure the version upgradation from 9.8(4)29 to 9.12.4.67? What are pre-requisites ?
IP direct-broadcast with standard vs extended ACL
I need to enable directed broadcasts on some SVIs. Is there any difference between me using these two configs:acl 1 permit 10.10.10.1int vlan 1ip directed-broadcast 1ip forward-protocol udp 10ORacl 2000 permit 10.10.10.1 any udp 10int vlan 1ip direct...
PLATFORM-FCA-2-TX_RX_TIMEOUT on ASR9010
Hi,Anyone experience receiving below syslog? What would be the cause of this? Thanks in advanceLC/0/1/CPU0:Apr 11 16:38:10.172 : pfm_node_lc[305]: %PLATFORM-FCA-2-TX_RX_TIMEOUT : Clear|lda_server[36897]|0x1032006|Device driver for device 'Tom_POLLER6...
Power Given, but Power Controller does not report power good C9200L
Hi, i have Access Switch C9200L-48P-4X-E and Interface G1/0/1 is Uplink Trunk to Distribution Switch however, we are getting the below error for some:%ILPOWER-5-DETECT: Interface Gi1/0/1: Power Device detected: IEEE PD: %ILPOWER-5-IEEE_DISCONNECT: In...
Does ise patch installation cause downtime?
I'm trying to patch install 6ea ise consisting of pan/mnt and psn in version 3.2. Does downtime occur between tasks?
Routing incoming traffic
This is getting really frustrating. Every time I try to ask this question it's tacked on to a different thread about a different question that is already answered, so no one answers. I am trying to routing incoming traffic to my Exchange server. As f...
Enterprise Agreement Educational Tutorials
The Enterprise Agreement (EA) onboarding process aims to equip customers with essential knowledge for effective asset management. These resources provide comprehensive guidance on EA principles and tools, enabling seamless EA-software management thr...
Cisco IR829 does not get ip address
hello i am trying to configure my cisco 829 with this simple code snipped but the device refuse to ping 8.8.8.8 or 0.0.0.0 etc and the cellular 0/0 or 1/0 refuse to get ip address, i use a generic sim card and i dont know if the problem is related t...
If I disable ap status on c9800, will I not radiate the radio?
I'm trying to do an ap name (ap hostname) shutdown on 9800 cli to turn off the ap radio. If I disable the status with that command, does it even turn off the radio?
ISE- Profiling question
Hello! about profiling in ISE,I have seen in several tutorials that it is recommended to put a policy with an authorization profile (lets call it PROFILING) before the default bottom policy one named "Default". This PROFILING profile would have a dAC...
the incoming calls that are in the Attendant Console Standard queue
How to make it possible to view the incoming calls that are in the Attendant Console Standard queue?, since the operators do not see which one has the longest waiting time and provide the corresponding attention.I have CUAC version 14.02
Switch config for ports with dot1x and MAB at same time - auth order
Hello, I almost always see this command as best practice authentication order dot1x mab , but sometimes I see this as best practice authentication order mab dot1x. The priority is always this: authentication priority dot1x mab -when I have PC (dot1x)...
