Hi , OSPF totaly stub area on nexus 7706 dont want to announce default route on interface vlan. Only when i 3 times reset ospf process or only when delete inteface vlan and add it again it starts announce default route. Only after that it start to s...
Forum Posts
Hi All, A quick design question (hopefully) regarding vPC orphan ports. We have a pair of Nexus 5K switches that are configured in a vPC domain that need to provide connectivity to a couple of access switches. The access switches only have single u...
Resolved! N3K MIB's
Hi guys, I was wondering if there's an option to download all the MIB's of a specific N3K model - C31128PQ. I know there is an option to run snmp-walk but this is not an option right now.
Hey All, Quick question hopefully. I have Nexus 9K vPC deployment with a number of VLANs that are used to provide connectivity to two Cisco ASA firewalls in a HA pair. The ASA firewalls are single attached to each peer switch and do not use port-...
I have a Type-2 consistency status: failed, on my implementation of vPC Domain. I understand that I need the same resources about VLANs and SVIs configured on both switches, but I implemented OSPF with different SVIs, and I understand that this is ...
Resolved! Nexus 5500 Remove Layer 3 License
I have a pair of Nexus 5500 switches that were previously used with layer 3 daughter cards. I would like to perform an ISSU on them, but am prevented by the presence of the LAN Base license. I can't seem to find any documentation on how to remove t...
Hi All, I have problem with my multicast traffic, the topology like this: Configuration on nexus 7000 Box 1: interface Vlan951 ip address 10.204.137.66/27 ip ospf passive-interface ip router ospf 1 area 0.0.0.207 hsrp 951 ...
Hi , What is SU and SD mean in the below output. I am seeing there is a mac flap between P015 and few interfaces.Po15 is down and when I see sh run config of that port channel no po15 , there is no configuration which means is it configured or n...
(Bit of a newbie when it comes to 1000V. Apologies in advance if I'm using the wrong terminology.) I have two separate 1000V environments and both worked perfectly up until a few days ago. Now, however, one of them has stopping syncing up with vCente...
Resolved! Nexus 5020 licensing
Am I correct in saying that the N5000-AS is already included in the NX-OS and is free to use. Or do I need to install it? Or do I only need to install the additional ones such as N5020-SS after purchased.
Planning to upgrade our Cisco Catalyst 6807xl Sup6T VSS clusters 15.4 (1) SY2-> 15.5 (1) SY1 Can we do it with ISSU or eFSU to get as little interruption as possible? Finds no information about it when I go from 15.4 (1) SY2-> 15.5 (1) SY1
WS-C4500X-32SFP+ V06 is in rommon. I need to make it a standalone switch and no longer a VSS pair. This switch was once deployed as a VSS pair. It is going to be repurposed but as a standalone switch. Currently it is in rommon. How can I make it a st...
Hi NXOS Gurus.I'm planning upgrade to 7.1(4)N1(1) of the series of N5K switches running quite old images like mentioned in the tytle.reading the release notes to target version (https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/u...
Resolved! VPC status down NX 5k
Quick question. I'm adding some vpc ports to a switch which has vpc already configured on it. The fibers will run to a server. I've pre-configured the port-channel and interfaces. The fibers are plugged in to the switch but not yet to the server....
Resolved! Nexus 5596 upgrade
Hi All, I have a pair of Nexus 5596 running in vpc with old firmware( 5.1) and there are 8 fex connected to the N5K. Basically the N5K is only used for basic layer 2 function only (without FC). We are planning to upgrade the N5K to the version...
