Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, I have a CME 7.1 with fourteen 7911 ip phones and four 4942 phones. When I place a call from any phone it gets a busy tone at random times, and I need to call several times to the same number until the call goes through.Does anyone has experi...
Hi all, I'm having some issues while im trying to upgrade cucm .I have used different clients however with no succes.issues like :wrong username passwordcould not connect to remote location. Filezillasolarwindsfreeftpdcore ftp None of these have work...
when an agent selects the "New Call" soft button to initiate a call the line chosen is whichever line was last used / selected. We would like to have this updated so that the "New Call" button also defaults to the primary extension in the same way th...
Hi, I'm trying to set up one of our receptionist lines to roll over to another line if the receptionist doesnt answer. I beleive I have things configured correctly, but it doesnt appear to work. Here is a screen shot from within Call Manager 10.5. ...
Hi Guys I am trying to add new phone , but it showing status rejected every time even phone is not connected.I have readded manually many times but issue still the same and when i change the Mac then its fine . . CUCM 11.5.Please advise
Hi!I have an issue with my cucm 10.5.I have a sip trunk that is connected to the telephone service provider, and when someone calls to another user of the same cucm, but dialing the long number (the number providade by the telephone service provider ...
Dear all,I am having an issue with Cisco 3905 SIP phone on CUCME. The time displayed on all the phones is incorrect. More secifically the phones display the time as GMT and not the correct time zone.Here is my voice register global config:voice regis...
We are facing issue with Cisco IP Phone 7821 model.... CME 10.5 version we are using ..IP Phone is not registering ...when we go to the setting its ask us for credentials to check the settings ..where we are trying to check IP address parameters. one...
We've hit BugID CSCul26124 ("Time wrong on a 7841 phone") The public bug details offer no help. Has anyone got any suggestions for working around this? Thanks, GTG
Im using a SIP provider (voip.ms) to a H323 gateway (2801) and from there go to my CUCM 8.6 server. Inbound calls work fine, i get ringback and outbound calls connect and work fine, i just hear no ringback on my outbound calls via my SIP provider.At...
I need to go on a VMWare course , Though I configure CUCM , UCCX, UCCE , Installs on MCS, Upgrades, ES etc. I have little experience from a Virtual point of view. I’ve seen various courses but not sure of the one to take - I`m not after the full cou...
Hi Team I have a doubt that in IP telephony environment, Can we use the same VLAN for VOice and DATA. For example : If I am using vlan 2 for data, so it may use for voice as well ?? Thanks in advance.
Hi,Please help to configure line appearance in expansion module ( Cisco 7915 12 button ) using CUCM.Thanks & Regards,Shaggy
Hi, Please consider following configuration: dial-peer voice 1 voip incoming called-number . dial-peer voice 2 voip incoming called-number . session protocol sipv2 Looking into documentation I did not find anywhere dial-peer protocol to be used for...
Hi All,I have a problem with an isdn circuit layer 2 and have been through other postings but none have helped so far.*Oct 2 12:06:49.391: %CONTROLLER-5-UPDOWN: Controller E1 0/1/0, changed state to down (AIS detected)*Oct 2 12:06:49.395: %ISDN-6-L...
