Hi Everyone, I need some support for connecting two different networks together. Below is the diagram of network, I want to connect to both network 192.168.128.xxx and 10.1.40.xxx from a PC connected to SW3. Currently I have a Layer 3 switch (SG 3...
So I'm trying to connect an HP Blade Chassis to our core switch, a Cisco 4500, WS-C4500X-16. These are set up as a stack. The chassis has two NICs that need to connect, so I'm connecting them to te1/1/10 and te2/1/10. If I connect the two NICs to ...
Anybody think this is too high for memory usage?KBCFR2SW05#sh memory free Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)Processor 2CD323C 79201732 67788360 11413372 10384280 982...
I HAVE SWITCH which is in rommon mode i can't do anything please help me tell me how to upload ios through rommon mode or which is the best way to upload ios fast still my switch 6509 in rommon mode i can,t do anything and how to boot it stil...
Hi, I have configured Object based ACLs on my Cisco 3850 switch (IOS 16.3.6). sample of two ACLs are show below. actually match hit counts are not shown in any ACLs although all the communication is successful. Please let me know why the ACL counters...
I need a help to solve a question about my Cisco C3650-24PD, when I enter the command: show enviroment temperature status, it displays: ASIC Temperature Value: 0 Degree Celsius. I just need to know if its a Hardware failure or IOS update issue, IOS V...
Hi, Is there anyone who can tell me exact functionality of each privilege level like what we can do at level 1 up to 15 levels. Thanks
Hi Team, I have cisco 7609,7606 where we are observing huge broadcast packets so i want to know possible ways to limit broadcast packets and interrupts. Please share the valid cisco document for the same .
Hello, Im trying to connect 2 hosts via a Cisco Catalyst 2960 switch. I want to send traffic between both hosts in 3 different VLANs (10,11 and 12). Both hosts are in the same subnet (172.16.10.0/24). I configured the switch as follows: -Host 1: co...
Hello, Recently I attempted to upgrade the IOS on some 3850 that I received. Somehow the process went wrong and started throwing Mainboard hardware authentication failed. Abort init ... Right after loading the kernel. Eventually using the emergenc...
Hi, I'm currently facing to an environment where a VPLS has been deployed as a "HUB" in the core of a campus LAN Network, not participating in Spanning-Tree The design principles are : - a root VSS is connected to a ASR920 VPLS Network, thanks to...
We have a Catalyst 4506 switch with Supervisor IV model WS-X4515, ROM version 12.2(20r)EW1, IOS version 12.2(52)SG.When connecting to this unit via SSH for administration from Linux (ex: Fedora 24, OpenSSH v7.2p2), fails with message: no matching ...
Cisco Nexus 5020 Firmware is upgraded. Upgrade was successfull without any issue. After reboot nothing comes up on the console. Tried rebooting a couple of times. nothing comes up on the console, not even the inital Bios output. Anybody know if its a...
See attached packet tracer diagram. Not quite sure what is going on here go 3 issues. 1. So the Interconnect Sw Primary is not able to ping the directly connected InterRt Primary. 2. Access Sw 1 can't ping any other sub intefaces on directly connec...
You can see the bgp topology table that I have two routes for 10.32.0.0/16. The one for EIGRP is put into the routing table even though BGP has the lower administrative distance. Can someone help me understand why this is the case? And how would I ch...
| User | Count |
|---|---|
| 11 | |
| 11 | |
| 10 | |
| 9 | |
| 6 |
