Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi We have just bought a SIP trunk for telephony service, but its a one way connection. Incoming calls succeed but outgoing calls fail. The following lines are outputs from "show ccsip all". to (STATE_DEAD, SUBSTATE_NONE)*May 12 05:27:29.515: //4/CF...
Hi Team, I have the below setup on a 2921 router running CME; 2 GSM gateways connected to the router's VIC FX0 ports. (072....... & 073.......) Internal extensions start with 2001 onwards I would like assistance on how to configure dial peers to allo...
Hey guys, right know, I want to get some basic knowledge about CME for my CCNA Collaboration. Therefore, I've got an 1861 Integrated Service Router. I currently have some struggle to connect to my 8961 IP Phone and my pc. Maybe I did some basic k...
Hi everyone. In my environment I have a CUBE (C2900-UNIVERSALK9-M), Version 15.6(2)T. CUCM-->CUBE-->Provider There is SIP Trunk (5060) configuration between CUCM to CUBE. The CUBE have a SIP Trunk to provider(not secure), I want to add a new SIP to...
Dear all I would like to know when I should use a separate TFTP Server! I have a cluster with two servers, one publisher and one subscriber! these two servers being used as TFTP servers. I would like to know when I should use a sperate TFTP serv...
I am trying normal password recovery for (cisco routers) for IAD 2400 but iam unable to get in rommon mode ? Help please.
Hi Guys I would like to know if is possible to restrict using FAC for a specific Cisco IP Phone. For example, there are two IP Phones A and B and there are two FACs ( 1111 and 2222). I want to make IP Phone A just accepts this FAC (1111) and IP Ph...
Dear Experts, We have installed Cisco Cisco Unified CM Administration System version: 10.5.1.10000-7 and connected to 7841, 7960. Recently we got some Cisco IP Phone 8845 but we can't able to see 8845 in listed phone. Kindly advise. Regards, Im...
Does anyone have any knowledge/experience of getting a Paxton Net2 door entry device registered to a CME as a third-party endpoint? We have a voice register pool device configured with a username and password, and this works becuase a SIP softphone ...
Hi everybody, I have been facing with a problem when we try to print or scan and a CP 7821 is connected in the middle of computer (node - CP Phone - PC). Users report that when they try to print or scan from their PC´s and CP 7821 is connected this...
Hi, We have a stack 2960 and all phones are Cisco 9951/9971. I'm looking at the config and all these commands are in an interface. Is it an overkill to have mls qos trust device cisco-phone, mls qos trust cos, and auto qos voip cisco-phone command ...
Hi Guys, My Customer have the solution with CUCM 10.5.2 and the a remote site there is a gateway with FXO. When I dial to number FXO interface and the User attend, ok, the call is completed. When I dial to FXO and there are not User to attend, in ...
Hi All, Currently my settings is never expire in the voicemail password policy. If i gave the cisco recommended days of 180, do my exisiting users in the voicemail server need to change their password immediately or they will get 180 days grace per...
I'd like to update many phones registered to our CUCM. I'd like to set the 'Device Pool' based on the first 3 octects of the phone's IP address. For example, if the phone is registered with an IP of 192.168.15.2 15 is my ACME office and I'd lik...
I've looked all over the net, and can't seem to find a similar solution. I'm currently receiving 10 digits from ITSP and would like to convert the Area Code and NPA of called number to two digit site code of say "10" + four digit extension, since my ...
